Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
B) HOW TO USE YOUR TRANSCEIVER
1) ON/OFF ~ VOLUME
Turn on radio: clockwise turn VOLUME knob (1) until radio emit beep and show
current channel, radio is on. Turn Off radio: counterclockwise turn VOLUME
knob (1)until radio emit click sound ,then radio is off.
Volume Adjustment: Radio is on, rotate VOLUME knob (1) to
LCD shows "UOLXX" for 5 seconds which means volume level. Total is 56 levels.
Clockwise to increase volume. Counterclockwise to decrease volume.
2) RF POWER
In TX, rotate RF PWR knob (2) to
wise to increase power. Counterclockwise to decrease power.
3) ASC (Automatic Squelch Control) ~ SQUELCH
Suppresses
undesirable background noises when there is no communication.
Squelch does not affect neither sound nor transmission power, but allows a
considerable improvement in listening comfort.
a) ASC: AUTOMATIC SQUELCH CONTROL
Worldwide patent, a PRESIDENT exclusivity.
Turn the SQUELCH knob (3) anti-clockwise into ASC position. "ASC" appears
on the LCD. No repetitive manual adjustment and a permanent improve-
ment between the sensitivity and the listening comfort when ASC is active.
This function can be disconnected by turning the switch clockwise. In this
case the squelch adjustment becomes manual again. "ASC" disappears
from the LCD, "SQL on" appears for 5 seconds.
b) MANUAL SQUELCH
Turn the SQUELCH knob clockwise to the exact point where all background
noise disappears. This adjustment should be done with precision as, if set to
maximum (fully clockwise), only the strongest signals will be received. LCD shows
"SQLXX" for 5 seconds which means squelch volume level. Total is 36 levels.
4) MENU
Press the MENU key (4) for 2 seconds to
"FUNC" appears on the LCD.
Use s/t keys (10) to
select
the desired function.
Use rotary PUSH knob (6) to
set
Press any key except PUSH knob (6) or wait for 5 seconds to
"FUNC" disappears from the LCD.
See § MENU FUNCTIONS for details, page 35.
adjust
adjust
FM/AM/USB/LSB output power. Clock-
enter
in the menu function setting.
the function.
store
5) MEM ~ STORE
MEM
(short press)
Press MEM key (5) to
Press s/t keys (10) on to
Press MEM key (5) again to
STORE
volume.
(long press)
Select
desired channel, band and modulation mode.
Long press MEM-STORE key (5) to
blinks in the LCD.
Rotate PUSH knob (6) to
Long press MEM-STORE key (5) until blinking memory disappeared. Storage
finished and
exit
Channel Storage Setting.
6) ROTARY "PUSH" KNOB
status, rotate PUSH knob (6) to
In
POWER ON
to increase, counterclockwise to decrease.
Press PUSH knob (6), "-"displayed under frequency which means adjust
frequency's stepping.
Push or rotate the PUSH knob (6) is also used to
7) CLARIFIER
This CLARIFIER knob (7), allows a frequency deviation during reception in
order to improve the clearness of your correspondent's voice.
8) MIC GAIN
In
POWER ON
status, rotate MIC GAIN knob (8) to
LCD shows "nIC XX" for 5 seconds which means microphone gain level. Total
is 56 levels Clockwise to increase, counterclockwise to decrease.
In
PA
status, rotate MIC GAIN knob (8) to
"nIC XX" for 5 seconds which means microphone volume level. Total is 56
levels. Clockwise to increase, counterclockwise to decrease.
9) RF GAIN
In RX, rotate RF GAIN knob (9) to
counterclockwise to decrease.
10) s/t CHANNEL/FREQUENCY SELECTOR
and exit.
s/t keys (10) allows
frequency number according the choose done in the [UP dn] menu (see §
s/t KEYS SETTING, page 36).
31
enter
into Memory Mode.
select
the pre-stored channel (6 memories).
exit
Memory Mode.
enter
into Channel Storage Setting, memory
select
the storage memory n1 ~ n6.
adjust
frequency. Clockwise
set
functions or parameters.
adjust
adjust
adjust
RX gain. Clockwise to increase,
increasing
or
decreasing
a channel number or a
microphone gain.
volume. LCD shows
Publicidad
Tabla de contenido
