General Power Tool Safety Warnings; Know Your Product; Operation - SPARKY HeavyDuty BU2 350 Instrucciones De Uso

sistance. Contact with electric lines can lead
to fire and electric shock. Damaging a gas line
can lead to explosion. Penetrating a water line
causes property damage or may cause elec-
tric shock.
▪ Always keep the cord away from the working
area of the power tool.
▪ Never use the machine with a damaged cable.
Do not touch the damaged cable and pull the
mains plug when the cable is damaged while
operating. Damaged cables increase the risk
of electric shock.
▪ Always be sure you have a firm footing. Be
sure no one is below when using the tool in
high locations.
▪ Use clamps or a vice to secure your work
whenever possible.
▪ Watch out for the initial torque reaction of the
machine or upon jamming the drill bit.
▪ Do not touch the drill bit or parts close to it dur-
ing operation and immediately after that; they
may be extremely hot. You may get serious
burns.
▪ Keep work area clean. Blends of materials are
particularly dangerous. Dust from light alloys
can burn or explode.
▪ Rags, cloths, cord, string and the like should
never be left around the work area.
▪ Always switch the machine off prior to leaving
it down.
▪ The tool must be used only for its prescribed
purpose. Any use other than those mentioned
in this Manual will be considered a case of
misuse. The user and not the manufacturer
shall be liable for any damage or injury result-
ing from such cases of misuse.
▪ To use this tool properly, you must observe
the safety regulations, the assembly instruc-
tions and the operating instructions found in
this Manual. All persons who use and service
the machine have to be acquainted with this
Manual and must be informed about its poten-
tial hazards. Children and frail people must not
use this tool. Children should be supervised at
all times if they are in the area in which the
tool is being used. It is also imperative that
you observe the accident prevention regula-
tions in force in your area. The same applies
for general rules of occupational health and
safety.
▪ The manufacturer shall not be liable for any
changes made to the tool nor for any damage
resulting from such changes.
▪ The power tools must not be used outdoors in
rainy weather, or in moist environment (after
rain) or in close vicinity with easily flammable
6
EN
liquids and gases. The working place should
be well lit.
V - Know your product
Before using the power tool, familiarize yourself
with all the operating features and safety re-
quirements.
Use the tool and accessories only for the appli-
cations intended. All other applications are ex-
pressly ruled out.
1. Three-jaw chuck
2. Place for fixing the spindle
3. Drill journal
4. Operation mode selector switch
5. Ventilation slots
6. Depth gauge
7. Auxiliary handle
8. Reversing switch (BUR2 350E)
9. Electronic regulator of rotation speed
(BUR2 350E)
10. ON/OFF switch
11. Lock-on button
12. Speed selector switch
13. Securing screw
VI - Operation
This power tool is supplied from single-phase al-
ternating current mains only. It is double in sulated
according to EN 60745-1 and IEC 60745 and
can be connected to grounded or not grounded
sockets. This power tool is radio suppressed in
compliance with EMC Directive 2004/108/EC.
The machine with mounted proper drill bit is suit-
able for impact drilling in stone, steel, wood, etc.
The machine is not designed for wet diamond
drilling in concrete!
PRIOR TO INITIAL OPERATION
▪ Make sure the power supply voltage corre-
sponds to the value indicated on the name
plate with technical data of the tool.
▪ Always check the position of ON/OFF switch.
The power tool must be connected to the
power supply socket only when this switch
is in OFF position. If the plug is connected to
a receptacle while the power switch is in the
ON position, the power tool will start operating
immediately, which could cause a serious ac-
cident.
▪ Make sure that the cord and the plug are in
order. If the replacement of the supply cord is
BU2 350 ● BUR2 350E