Worx WG782 Manual Del Usuario página 15

24v 14” cortacésped sin cables
Ocultar thumbs Ver también para WG782:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

2) Clip the plastic clips of the grass bag over
the metal frame. (Fig C3)
warNiNG: make sure to not fit the
handle in the reverse direction as it
will not remain secure. make sure to fit
the handle as shown in Fig C1.
3. aTTaChiNG ThE GraSS baG To ThE
mowEr (See Fig d1,d2,d3)
NoTE: The grass bag is held in place by
the safety flap.
1) Switch the mower off, remove the safety
key (6) and wait until the mower blade has
stopped.
2) Raise the safety flap (11) and hold it in the
upward position while the grass bag is
properly located below it (Fig D1)
3) Position the lower edge of the grass bag
on the plastic tabs (c) found below the rear
discharge chute on the mower deck. (Fig.
D2)
4) While holding the grass bag in position
lower the safety flap into its' final position.
It should rest on top of the grass bag with
the tabs of the grass bag being inserted
into the safety flap. Ensure the safety flap
locks securely into position with the grass
bag. (Fig D3)
NoTE: The two parts should smoothly
slide together with little force. They WILL
NOT "click" together.
NoTE: Depress the grass bag slightly to
ensure that it is completely installed.
4. rEmoViNG/EmPTyiNG ThE GraSS
baG
1) Switch the mower off, remove the safety
key (6) and wait until the mower blade has
stopped.
2) Hold the grass bag handle
3) Raise the safety flap (11) upward and hold
it in the upward position until the grass bag
is removed(Fig D1)
warNiNG! Before each use, always
check that the safety flap closes securely
over the rear discharge chute. Never lift the
safety flap (11) when the lawn mower is in
operation. The blade must be completely at
rest before handling the safety flap.
24V 14" Cordless lawn mower
5. FiTTiNG/rEmoViNG ThE baTTEry
(See E1,E2,E3,E4)
rEmoViNG baTTEry (12)
1) While gripping the battery handle lift it
upward without twisting or turning it. (See
E1)
FiTTiNG baTTEry
1) Locate the front and rear of the battery (Fig
E2)
2) Lower the battery into position. (See E3)
NoTE: For a secure fit, make sure the
battery tray is free of debris and the
contacts on the battery and in the
battery tray are clean (use a dry cloth
to clean) (E4)
NoTE: When fitting or removing the battery
be careful not to drop the battery onto your
foot or the ground.
OPERATION
1. STarTiNG aNd SToPPiNG (See F1,
F2,F3)
warNiNG! The blade continues to
rotate for a few seconds after the
machine is switched off. Allow the motor/blade
to stop rotating before switching "on" again.
Do not rapidly switch off and on.
STarTiNG
1) Insert safety key (6) into the housing of the
switch box. (See F1)
2) Slide the safety key to the right and hold in
position. (See fig F2)
3) Pull the switch lever towards the handle bar
and the mower will start. (See fig F3)
4) Release the safety key and begin mowing.
NoTE: The safety key will stay in the "on"
position as long as the operator holds the
lever tightly against the handlebar.
SToPPiNG
Release the switch lever and remove the
safety key.
2. iNSTalliNG mUlCh PlUG (15) (See G)
1) Turn the mower off, wait until the blade
stops and remove the safety key (6).
2) Raise the safety flap and hold it up.
15
15
EN

Publicidad

Tabla de contenido
loading

Tabla de contenido