Publicidad
ss03138
Connected to 2012 Ford Mustang Shelby GT500 5.4L
Read DTCs
Please select one or more controllers and tap 'Continue' to
start DTC scan.
PCM
GEM MODULE / TPMS
OCCUPANT CLASSIFICATION
AUDIO CONTROL MODULE
FRONT CONTROLS INTERFACE MODULE
2. Seleccione el controlador de vehículo deseado y
luego seleccione Continue.
ss03139
Connected to 2012 Ford Mustang Shelby GT500 5.4L | PCM
DTCs
Select Option
Read DTCs
KOEO
KOER
Reset KAM
3. Al tocar una opción en el menú, el usuario es llevado
a esa prueba. Siga las indicaciones que aparecen en
la pantalla.
ss03140
Connected to 2012 Ford Mustang Shelby GT500 5.4L | PCM
DTCs
Current Codes
B10A2-00
Crash Input
B1200-00
Crash Input Mismatch - CAN
Inactive Hardwired Active
B1207-00
Crash Input Hardwired Signal
4. Los DTC serán leídos desde el controlador de vehí-
culo seleccionado.
•
Seleccione un DTC de la lista para la Información
de Diagnóstico Relacionada. Consulte la sección
Información de Diagnóstico
•
Si un DTC posee un Criterio de Código disponi-
ble, existirá un "*" junto al DTC.
Bosch Automotive Service Solutions Inc
Change Vehicle
Select All
Deselect All
ABS / TRACTION CONTROL
AIRBAG
ACCESSORY PROTOCOL INTERFACE
BODY CONTROL MODULE
FRONT DISPLAY INTERFACE MODULE
Continue
Change Vehicle
Change Vehicle
Clear DTCs
Refresh
Share
Save
Self Diag
Details
Details
Details
Manual DTCs
11:41
Ciertos vehículos no son compatibles con el protocolo
Home
DTC estándar y requerirán un proceso manual para
recuperar y eliminar códigos.
ss03141
Connected to 2002 Subaru Forester Base 2.5L | ABS
DTCs
Manual Codes Procedure
1) Take out diagnosis connector from side of driver's seat heater unit.
2) Turn ignition switch Off.
3) Connect diagnosis connector terminal 6 to diagnosis terminal.
4) Turn ignition switch On.
5) ABS warning light is set in the diagnostic mode and blinks to identify trouble code.
6) After the start code (11) is shown, the diagnostic trouble codes (DTC) will be shown in
1. Siga las indicaciones que aparecen en la pantalla
para recuperar los DTC.
Home
ss03142
Connected to 2002 Subaru Forester Base 2.5L | ABS
DTCs
Manual Codes Procedure
1) Take out diagnosis connector from side of driver's seat heater unit.
2) Turn ignition switch Off.
3) Connect diagnosis connector terminal 6 to diagnosis terminal.
4) Turn ignition switch On.
5) ABS warning light is set in the diagnostic mode and blinks to identify trouble code.
6) After the start code (11) is shown, the diagnostic trouble codes (DTC) will be shown in
2. Botón Select Library.
ss03143
Connected to 2002 Subaru Forester Base 2.5L | ABS
11:42
DTCs
Home
DTCs
11
Manual Codes Procedure
21
1) Take out diagnosis connector from side of driver's seat heater unit.
2) Turn ignition switch Off.
22
3) Connect diagnosis connector terminal 6 to diagnosis terminal.
4) Turn ignition switch On.
23
5) ABS warning light is set in the diagnostic mode and blinks to identify trouble code.
6) After the start code (11) is shown, the diagnostic trouble codes (DTC) will be shown in
3. Siga las indicaciones que aparecen en la pantalla.
ADS 325 | Manual de usuario | 31 | es
Change Vehicle
Clear DTCs
Refresh
Share
Save
Change Vehicle
Clear DTCs
Refresh
Share
Save
Change Vehicle
Start Code: Trouble Code Is Shown
Clear DTCs
Refresh
Share
Save
After Start Code Only Start Code Is
Shown In Normal Condition
Abnormal ABS Sensor (Open Circuit Or
Input Voltage Too High) - Front Right
ABS Sensor
Abnormal ABS Sensor (Abnormal ABS
Sensor Signal) - Front Right ABS
Sensor
Abnormal ABS Sensor (Open Circuit Or
Close
1699501021 | REV. A | 07.2018
11:44
Home
Code Assist
11:44
Home
Code Assist
11:44
Home
Code Assist
Publicidad
Capítulos
