Stanley FATMAX FMEG615 Traducido De Las Instrucciones Originales página 10

ENGLISH (Original instructions)
To avoid accumulation of metal chips in the interior of the
grinder, we recommend cleaning the ventilation ducts daily.
Refer to Maintenance.
Warning! Metal powder accumulates.
Excessive use of the grinding wheel on metals may increase
the risk of electric shock. To reduce the risk, insert the RCD
before use and clean the ventilation ducts daily. Follow the
maintenance instructions below to blow dry compressed air
into the ventilation ducts.
Grinding
Surface Grinding with Grinding Wheels
Allow the tool to reach full speed before touching the tool
u
to the work surface.
Apply minimum pressure to the work surface, allowing
u
the tool to operate at high speed. Grinding rate is greatest
when the tool operates at high speed.
Maintain a 20˚ to 30˚ angle between the tool and work
u
surface.
Continuously move the tool in a forward and back motion
u
to avoid creating gouges in the work surface.
Remove the tool from work surface before turning tool off.
u
Allow the tool to stop rotating before laying it down.
Precautions to take when sanding paint
Sanding of lead based paint is NOT RECOMMENDED
u
due to the difficulty of controlling the contaminated dust.
The greatest danger of lead poisoning is to children and
pregnant women.
Since it is difficult to identify whether or not a paint
u
contains lead without a chemical analysis, we recommend
the following precautions when sanding any paint.
Helpful Hints
Hold your angle grinder with one hand on the body and
u
the other hand firmly around the side handle as shown in
Fig. E.
Always position the guard so that as much of the
u
exposed disc as possible is pointing away from you. ff Be
prepared for a stream of sparks when the disc touches the
metal.
Maintain an angle between the disc and work surface
u
(Fig.D) of approximately 30° when grinding and 10°- 15°
when sanding for best tool control, material
removal, and minimal loading.
Caution! Use extra care when grinding into a corner
as a sudden, sharp movement of the grinder may be
experienced when the wheel contacts a secondary surface.
Warning! Always wear eye protection while
operating this power tool.
Cutting metal
When cutting, work with moderate feed, adapted to the
material being cut.
10
Do not exert pressure onto the cuttingndisc, tilt or oscillate the
machine.
Do not reduce the speed of running down cutting discs by
applying sideward pressure.
The machine must always work in an upgrinding motion.
Otherwise, the danger exists of it being pushed uncontrolled
out of the cut.
When cutting profiles and square bar, it is best to start at the
smallest cross section.
Maintenance
Your STANLEY FATMAX corded/cordless appliance/tool has
been designed to operate over a long period of time with a
minimum of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
Warning! Before performing any maintenance on corded/
cordless power tools:
Switch off and unplug the appliance/tool.
u
Or switch off and remove the battery from the appliance/
u
tool if the appliance/tool has a separate battery pack.
Or run the battery down completely if it is integral and then
u
switch off.
Unplug the charger before cleaning it. Your charger does
u
not require any maintenance apart from regular cleaning.
Regularly clean the ventilation slots in your appliance/tool/
u
charger using a soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth. Do
u
not use any abrasive or solvent-based cleaner.
Regularly open the chuck and tap it to remove any dust
u
from the interior (when fitted).
Mains plug replacement (U.K. & Ireland only)
If a new mains plug needs to be fitted:
Safely dispose of the old plug.
u
Connect the brown lead to the live terminal in the new
u
plug.
Connect the blue lead to the neutral terminal.
u
Warning! No connection is to be made to the earth terminal.
Follow the fitting instructions supplied with good quality plugs.
Recommended fuse: 13 A.
Troubleshooting
Problem Possible cause
Unit will not start. Cord not plugged in.
Cord or switch is
damaged.
Possible solution
Plug tool into a
working outlet.
Have cord or switch replaced
at a Stanley FatMax service
center or authorized
servicer.)