Stel TIG μP 353H DC Manual De Instrucciones página 51

ENGLISH
TIG µP 353H DC
COD. 6903700030
mode led lights up (ref.4D page 9)
2) For 2 seconds the displays (ref.20-21 page 9) will show the letters Pun.
3) Regulating the welding current – proceed as described for TIG 2 TIME
welding.
4) Regulating the spot welding time – Pressing the SU button (ref.8 page 9)
selects the spot welding time. The right-hand display A (ref.20 page 9) will start to
blink indicating the value that can be selected with the encoder (ref.5 page 9) from
0.1 to 10 seconds.
To view the set value at any time, briefly press the SL button.
6) Regulating the post-gas time - proceed as described for TIG 2 TIME welding.
7) Activating and regulating DC pulse – proceed as described for TIG 2 TIME
welding.
8) Activating and regulating AC mode – proceed as described for TIG 2 TIME
welding.
9) If you want to work with a remote control (CAD), refer to the chapter on
PREPARING THE REMOTE/PEDAL CONTROL on page 20.
Procedure for TIG SPOT WELDING with HF start
Starting welding:
1) Press the HF ON button (ref.7 page 9); the HF ON led lights up (ref.7A page 9).
2) Bring the tip of the electrode (tungsten) close to the piece to be welded.
3) Press the torch button: after 0.5 seconds of PRE-GAS, the arc is lit by the HF
generator and the welding process starts.
End of welding:
1) The arc goes out automatically after the time regulated by means of the SU
button (ref.8 page 9); then there will be the POST-GAS time set by means of the
PG button (ref.17 page 9).
Procedure for TIG SPOT WELDING with LIFT start (without HF)
Starting welding:
1) Check that the HF ON led (ref.7A page 9) is off. If it is not, press the HF ON
button (ref.7 page 9); the HF ON led (ref.7A page 9) goes off.
2) Bring the tip of the electrode (tungsten) into contact with the piece to be welded.
3) Press the torch button: after 0.5 seconds of PRE-GAS, lift the torch from the
side so as to move slightly away from the piece to be welded and start the welding
process.
End of welding:
1) Perform the same procedure described for TIG Spot Welding with HF start.
STEL s.r.l. – Via del Progresso n° 59 – 36020
Loc. Castegnero (VICENZA) - ITALY
TEL. +39 444 639525 (central.) – +39 444 639682 (comm.)
FAX +39 444 639641 – E-mail:stelgroup.com
http: www.stelgroup.it
TECHNICAL DESCRIPTION
51
ENGLISH
TIG µP 353H DC
COD. 6903700030
mode led lights up (ref.4D page 9)
2) For 2 seconds the displays (ref.20-21 page 9) will show the letters Pun.
3) Regulating the welding current – proceed as described for TIG 2 TIME
welding.
4) Regulating the spot welding time – Pressing the SU button (ref.8 page 9)
selects the spot welding time. The right-hand display A (ref.20 page 9) will start to
blink indicating the value that can be selected with the encoder (ref.5 page 9) from
0.1 to 10 seconds.
To view the set value at any time, briefly press the SL button.
6) Regulating the post-gas time - proceed as described for TIG 2 TIME welding.
7) Activating and regulating DC pulse – proceed as described for TIG 2 TIME
welding.
8) Activating and regulating AC mode – proceed as described for TIG 2 TIME
welding.
9) If you want to work with a remote control (CAD), refer to the chapter on
PREPARING THE REMOTE/PEDAL CONTROL on page 20.
Procedure for TIG SPOT WELDING with HF start
Starting welding:
1) Press the HF ON button (ref.7 page 9); the HF ON led lights up (ref.7A page 9).
2) Bring the tip of the electrode (tungsten) close to the piece to be welded.
3) Press the torch button: after 0.5 seconds of PRE-GAS, the arc is lit by the HF
generator and the welding process starts.
End of welding:
1) The arc goes out automatically after the time regulated by means of the SU
button (ref.8 page 9); then there will be the POST-GAS time set by means of the
PG button (ref.17 page 9).
Procedure for TIG SPOT WELDING with LIFT start (without HF)
Starting welding:
1) Check that the HF ON led (ref.7A page 9) is off. If it is not, press the HF ON
button (ref.7 page 9); the HF ON led (ref.7A page 9) goes off.
2) Bring the tip of the electrode (tungsten) into contact with the piece to be welded.
3) Press the torch button: after 0.5 seconds of PRE-GAS, lift the torch from the
side so as to move slightly away from the piece to be welded and start the welding
process.
End of welding:
1) Perform the same procedure described for TIG Spot Welding with HF start.
STEL s.r.l. – Via del Progresso n° 59 – 36020
Loc. Castegnero (VICENZA) - ITALY
TEL. +39 444 639525 (central.) – +39 444 639682 (comm.)
FAX +39 444 639641 – E-mail:stelgroup.com
http: www.stelgroup.it
TECHNICAL DESCRIPTION
51