Stel TIG μP 353H DC Manual De Instrucciones página 53

ENGLISH
TIG µP 353H DC
COD. 6903700030
time set by means of the PG button (ref.17 page 9).
Procedure for TIG WELDING WITH RESET (DOUBLE PARAMETER) with LIFT
start (without HF)
Starting welding:
1) Check that the HF ON led (ref.7A page 9) is off. If it is not, press the HF ON
button (ref.7 page 9) ; the HF ON led goes off (ref.7A page 9) .
2) Bring the tip of the electrode (tungsten) into contact with the piece to be welded.
3) Press the torch button: gas will come out immediately, lift the torch from the side
so as to move slightly away from the piece to be welded and start the welding
process; the current will go to the base value selected with the bC button (ref.15
page 9).
4) When the torch button is released the current will go to the set value A with a
slope up value selected with the SU button (ref.8 page 9).
By pressing the torch button briefly (less than 0.5 seconds), you can pass
directly from the set current value A to the final current value FC and vice
versa.
End of welding:
1) Follow the same procedure described for TIG WELDING WITH RESET
(DOUBLE PARAMETER) with HF start.
FUNCTION OF STORING AND LOADING WELDING
PARAMETERS (JOB MODE)
Function active for all welding modes
This function allows you to store and load all the settings made on the generator at
any time. It is possible to save 99 welding parameters (settings) .
STORING WELDING SETTINGS
1) Hold down simultaneously for 1 second the buttons bC (ref.15 page 9) and PG
(job mode) (ref.17 page 9); you will hear a double sound of the buzzer and the
letters PrG will blink on the left-hand display (ref.21 page 9) .
2) With the encoder A (ref.5 page 9) select the number of the programme in which
you want to save the welding parameters .
3) Hold down the HF ON button (ref.7 page 9) for more than 2 seconds; you will
hear 4 sounds of the buzzer and the letters Sto will blink on the left-hand display
(ref.21 page 9). At this point the programme has been saved and you can continue
using the machine.
LOADING STORED WELDING PROGRAMMES
STEL s.r.l. – Via del Progresso n° 59 – 36020
Loc. Castegnero (VICENZA) - ITALY
TEL. +39 444 639525 (central.) – +39 444 639682 (comm.)
FAX +39 444 639641 – E-mail:stelgroup.com
http: www.stelgroup.it
TECHNICAL DESCRIPTION
53
ENGLISH
TIG µP 353H DC
COD. 6903700030
time set by means of the PG button (ref.17 page 9).
Procedure for TIG WELDING WITH RESET (DOUBLE PARAMETER) with LIFT
start (without HF)
Starting welding:
1) Check that the HF ON led (ref.7A page 9) is off. If it is not, press the HF ON
button (ref.7 page 9) ; the HF ON led goes off (ref.7A page 9) .
2) Bring the tip of the electrode (tungsten) into contact with the piece to be welded.
3) Press the torch button: gas will come out immediately, lift the torch from the side
so as to move slightly away from the piece to be welded and start the welding
process; the current will go to the base value selected with the bC button (ref.15
page 9).
4) When the torch button is released the current will go to the set value A with a
slope up value selected with the SU button (ref.8 page 9).
By pressing the torch button briefly (less than 0.5 seconds), you can pass
directly from the set current value A to the final current value FC and vice
versa.
End of welding:
1) Follow the same procedure described for TIG WELDING WITH RESET
(DOUBLE PARAMETER) with HF start.
FUNCTION OF STORING AND LOADING WELDING
PARAMETERS (JOB MODE)
Function active for all welding modes
This function allows you to store and load all the settings made on the generator at
any time. It is possible to save 99 welding parameters (settings) .
STORING WELDING SETTINGS
1) Hold down simultaneously for 1 second the buttons bC (ref.15 page 9) and PG
(job mode) (ref.17 page 9); you will hear a double sound of the buzzer and the
letters PrG will blink on the left-hand display (ref.21 page 9) .
2) With the encoder A (ref.5 page 9) select the number of the programme in which
you want to save the welding parameters .
3) Hold down the HF ON button (ref.7 page 9) for more than 2 seconds; you will
hear 4 sounds of the buzzer and the letters Sto will blink on the left-hand display
(ref.21 page 9). At this point the programme has been saved and you can continue
using the machine.
LOADING STORED WELDING PROGRAMMES
STEL s.r.l. – Via del Progresso n° 59 – 36020
Loc. Castegnero (VICENZA) - ITALY
TEL. +39 444 639525 (central.) – +39 444 639682 (comm.)
FAX +39 444 639641 – E-mail:stelgroup.com
http: www.stelgroup.it
TECHNICAL DESCRIPTION
53