DeWalt DCN890 Traducido De Las Instrucciones Originales página 49

Each D WALT nailer is equipped with a trigger lock-off
e
when pushed to the right as shown in Figure E, prevents the
tool from firing a pin by locking the trigger and bypassing
power to the motor.
When the trigger lock-off is pressed to the left, the tool will be
fully operational. The trigger lock-off should always be locked off
(Fig. E) whenever any adjustments are made or when tool is not
in immediate use.
NOTICE: Do not store tool with battery pack installed. To
prevent damage to the pack and to ensure best battery
life, store battery packs out of the tool or charger in a cool,
dry location.
Loading the Tool (Fig. F)

WARNING: Keep the tool pointed away from yourself and
others.

WARNING: Never load pins with the contact trip or trigger
activated.

WARNING: Always remove battery pack before loading or
unloading pins.

CAUTION: Keep fingers clear of pusher latch track to
prevent injury.

WARNING: The trigger lock-off should always be engaged
whenever any adjustments are made or when tool is not
in use.

WARNING: Fasteners used to install metal connectors
must meet the requirements of the applicable building
codes and must be installed in compliance with code
requirements and metal connector hardware supplier
specifications. Failure to properly install connectors may
result in structural failures.
1. Turn the nailer upside down.
2. Slide the spring-loaded pusher latch
magazine to lock it into place.
3. Drop pin strips into the loading slot of the magazine,
making sure the pin heads align correctly with the slot
opening. (Refer to Technical Data to determine compatible
size.)
4. Keeping fingers clear of the track, close the magazine by
releasing the pusher latch. Carefully allow the latch to slide
forward and engage the pin strip.
Unloading the Tool

WARNING: The trigger lock-off should always be locked
off whenever any adjustments are made or when tool is
not in use.
1. Remove the battery from your nailer.
2. Slide the spring-loaded pusher latch to the base of the
magazine to lock it into place.
3. Tip the tool up until the fastener strip slides freely out of the
magazine.
4. With battery removed, check the nosepiece to verify there
are no pins remaining.
nOTE: The tool is equipped with a magnet in the nose area for
improved tool performance. When unloading, always verify that
which the small sticks of pins are not held to the magnetized nose
2
piece.
Speed Setting Summary (Fig. A, G, H)
This nailer is equipped with a speed selection switch
the tool when driving into different materials.
Speed 1: Softer materials (low strength concrete/cinder block)
Speed 2: Medium hardness materials (High strength concrete)
Speed 3: Hard materials (Structural steel)
In the event pins are not driving to depth in speed 1, you may
have to switch to speed 2 or 3 for additional driving power.
Speed Setting

The tool can be fired/actuated by pulling the trigger
of two modes: sequential mode or RapidCycle mode. Refer
to Selecting the Mode for detailed instructions for firing in
each mode.
Selecting the Mode (Fig. A, G)
15 to the base of the To select standard sequential mode, slide the mode selector
switch
To select rapid sequential operating mode (RapidCycle), slide
the mode selector switch
icon.
nOTE: Battery life in RapidCycle mode will be shorter than
in standard sequential mode. Leaving the tool in standard
sequential will give maximum battery life.
Sequential Mode
The sequential mode is used for intermittent nailing. It offers the
maximum battery life for driving pins.
1. Using the mode selector switch
2. Release the trigger lock-off
3. Push the contact trip
4. Pull the trigger switch
5. Release the trigger and raise the nailer from the
6. Repeat steps 3–5 to actuate the next nail.
RapidCycle Mode
In RapidCycle mode, the motor rotation speed is automatically
restored after driving a pin to allow fast consecutive nailing.
NOTICE: Driving pins into soft materials at high
speed settings will cause excessive wear to your tool
and may result in early failures.
Application
Fastening Steel/Wood to Low Strength
1
Concrete/Masonry (<27.5 MPa)
Fastening Steel/Wood to High Strength
2
Concrete (>27.5 MPa)
Fastening to structural steel;
3
50 mm x 100 mm Wood to Concrete
WARNING: Pins must be driven straight into the material.
Do not tilt nailer while driving fasteners. Refer to Fig. H.
Pin retention values improve when the tool is fired
perpendicular to the material.
4 to display the single arrow ( ) icon.
4 to display the double arrow (
sequential mode.
2 .
against the work surface.
6
1 to actuate the tool.
work surface.
EnGLIsh
to adjust
3
Typical Pin Length
19-25 mm
19-29 mm
13-57 mm
in one
1
)
4 , select the
47