Fein KBH25-2U Manual Del Usuario página 19

OBJ_BUCH-0000000141-003.book Page 19 Friday, February 19, 2016 11:15 AM
Character Unit of measurement,
international
Ø mm
mm
Fe
mm
Al
mm
mm
Fe
mm
Al
mm
mm
mm
kg
L dB
pA
L
dB
wA
L dB
pCpeak
K...
2
m/s
2
m/s
h,D
2
m/s
h,D
m, s, kg, A, mm, V,
W, Hz, N, °C, dB,
min, m/s
For your safety.
Read all safety warnings and all
WARNING
instructions. Failure to follow the
warnings and instructions may result in electric shock,
fire and/or serious injury.
Save all warnings and instructions for future reference.
Do not use this power tool before you have thor-
oughly read and completely understood this
Instruction Manual and the enclosed "General
Safety Instructions" (document number
3 41 30 054 06 1). The documents mentioned should be
kept for later use and enclosed with the power tool,
should it be passed on or sold.
Please also observe the relevant national industrial safety
regulations.
Intended use of the power tool:
hand-held core drill for drilling in wood, metal, plastic,
ceramics and tapping in weather-protected environments
without water supply using the application tools and
accessories recommended by FEIN.
This power tool is also suitable for use with AC genera-
tors with sufficient power output that correspond to the
Standard ISO 8528, design type G2. This Standard is par-
ticularly not complied with when the so-called distortion
factor exceeds 10 %. When in doubt, please refer to the
generator instruction/specification guide.
Unit of measurement,
national
mm
mm
mm
mm
mm
mm
mm
mm
mm
kg
dB
dB
dB
2
m/s
2
m/s
2
m/s
m, s, kg, A, mm, V,
W, Hz, N, °C, dB,
2 2
min, m/s
Explanation
Diameter of a round part
Drilling diameter, steel
Drilling diameter, aluminium
Drilling diameter, wood
Drilling capacity in steel (core drill bit)
Drilling capacity in aluminium (core drill bit)
Drilling capacity (hole saw)
Tap
d1 = Clamping range of drill chuck
d2 = Shank size of drilling shaft
d3 = Collar diameter
Weight according to EPTA-Procedure 01
Sound pressure level
Sound power level
Peak sound pressure level
Uncertainty
Vibrational emission value according to
EN 60745 (vector sum of three directions)
Mean vibrational value for core drilling in metal
Mean vibrational value for drilling with hole saw
Basic and derived units of measurement from
the international system of units SI.
Special safety instructions.
Use auxiliary handle(s), if supplied with the tool. Loss of
control can cause personal injury.
Hold power tool by the insulated gripping surfaces, when
performing an operation where the cutting accessory
may contact hidden wiring or its own cord. Cutting acces-
sory contacting a "live" wire may make exposed metal
parts of the power tool "live" and could give the opera-
tor an electric shock.
Wear personal protective equipment. Depending on appli-
cation, use face shield, safety goggles or safety glasses.
As appropriate, wear dust mask, hearing protectors,
gloves and workshop apron capable of stopping small
abrasive or workpiece fragments. The eye protection
must be capable of stopping flying debris generated by
various operations. The dust mask or respirator must be
capable of filtrating particles generated by your opera-
tion. Prolonged exposure to high intensity noise may
cause hearing loss.
Beware of any concealed electric cables, gas or water
conduits. Check the working area before commencing
work, e. g. with a metal detector.
Avoid contact with the core, which is automatically thrust
out by the pilot bit after the working procedure. Contact
with the hot or falling down core can lead to injury.
en
19