Installation Height; Installation Steps - Kerbl HAPPYCOW Uno Instrucciones De Uso

Tip
Secure the unit to an even, solid concrete wall.

5.3.1 Installation height

The suspension height of the unit must be adapted to the average withers height of the animals. The front lower edge of the brush should be at
the same height as the animals' average withers height (e.g. 1350 mm). The suspension height must be determined before the mounting holes
are made!
If there are considerable differences in withers height among the herd (more than 20 cm), the suspension height should be orientated towards the
larger animals in order to avoid rapid wear of the brushes.
1200 mm
Figure 2: Mounting height

5.3.2 Installation steps

1. Determine the installation height (see Point 5.3.1)
2. Install the unit at the determined height.
3. If necessary, attach protection against chewing to the connection cable.
4. If necessary, attach the optional protection bar
Tip
The control with display, the contact switch and the motor are not visible or accessible from the outside. The machine can be swung away
from the wall to gain access to the contact switch and control and to view the display.
To do this, either loosen the two screw attachments on the left or right side of the machine connecting the basic platform to the external
housing. (Figure 4 + 5.)
Even during installation, ensure that the connection cable is positioned so that the machine can be swung away from the wall.
Abb. 2
Abb. 2
1200 mm
Ø
Ø
Withers
Withers
height
height
FLOOR
FLOOR
Abb. 3
405 mm
FLOOR
Figure 3: Hole pattern
FINISHED SURFACE:
WEIGHT IN GRAMM
Albert KERBL GmbH Felizenzell 9 D-84428 Buchbach
l l
(WITHOUT FINISHED SURFACE):
Fon +49 (0)8086 - 933-100 Fax +49 (0)8086 - 933-500 Albert KERBL GmbH Felizenzell 9
l l
1310432,150 g
Mail info@kerbl.com www.kerbl.com
l Fon +49 (0)8086 - 933-100
Mail info@kerbl.com
DRAW
CHECK
NORM
ARTICLE NUMBER
KERBL:
18680; 18690; 18700
STAT. REVISION NOTE DATE NAME Urspr.
STAT. REVISION NOTE
42
Abb. 3
Ø
Ø
Withers
Withers
height
height
405 mm
FLOOR
1:20
SCALE DET. SCALE
FINISHED SURFACE: 1:20
SCALE
ISO 5456-2 Projection
MATERIAL: BASE SIZE/SEMI-FINISHED PART
methode1 ISO 5456-2 Projection
MATERIAL:
methode1
General tolerances
WEIGHT IN GRAMM
D-84428 Buchbach ISO 2768 - mK
l General tolerances
(WITHOUT FINISHED SURFACE):
Fax +49 (0)8086 - 933-500
l ISO 2768 - mK
1310432,150 g
www.kerbl.com DATE NAME
l TITLE:
DATE NAME
TITLE:
4.8.2021 sreinthaler
HappyCow UNO - Wall mounted
DRAW 4.8.2021 sreinthaler
HappyCow UNO - Wall mounted
CHECK
ASM
ASM
NORM
UNLESS OTHERWISE SPECIFIED:
DIMENSIONS ARE IN MILLIMETERS
UNLESS OTHERWISE SPECIFIED:
PROJECT NUMBER DIMENSIONS ARE IN MILLIMETERS
DWG NO.
KERBL:
ARTICLE NUMBER PROJECT NUMBER
DWG NO.
27376
KERBL: KERBL:
27376
18680; 18690; 18700
NAME Urspr.
DATE
1:10
1:10
DET. SCALE
BASE SIZE/SEMI-FINISHED PART
2
Blatt
2
3 Blatt
von von
3
von von
A3
A3