Bosch PSS 300 AE Manual Original página 11

cessive accumulation of powdered metal may cause elec-
trical hazards.
Secure the workpiece. A workpiece clamped with
u
clamping devices or in a vice is held more secure than by
hand.
Always wait until the power tool has come to a com-
u
plete stop before placing it down.
Products sold in GB only:
Your product is fitted with an BS 1363/A approved electric
plug with internal fuse (ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place by an au-
thorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
Product Description and
Specifications
Read all the safety and general instructions.
Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.
Please observe the illustrations at the beginning of this oper-
ating manual.
Intended Use
The power tool is intended for dry sanding of wood, plastic,
metal, filler and varnished surfaces.
Product Features
The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1) Orbital stroke rate preselection thumbwheel
(2) On/off switch
(3) Dust box, complete (microfilter system)
(4) Clamp
(5) Sanding plate
(6) Sanding sheet
(7) Extraction outlet
(8) Filter element (microfilter system)
a)
(9) Extraction hose
a)
(10) Dust extraction adapter
a)
(11) Punch
(12) Screws for sanding plate
a) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
Bosch Power Tools
Technical Data
Orbital sander
Article number
Rated power input
Orbital stroke rate preselec-
tion
No-load speed
No-load orbital stroke rate
Orbit diameter
Sanding sheet dimensions
– Hook-and-loop backing
– Clamping tension
Sanding plate dimensions
Weight according to
EPTA-Procedure 01:2014
Protection class
The specifications apply to a rated voltage [U] of 230 V. These spe-
cifications may vary at different voltages and in country-specific mod-
els.
Noise/Vibration Information
Noise emission values determined according
to EN 62841-2-4.
Typically, the A-weighted noise level of the power tool is:
Sound pressure level 84 dB(A); sound power
level 95 dB(A). Uncertainty K = 3 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 62841-2-4:
2 2
a = 10.0 m/s , K = 1.5 m/s ,
h
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
working period.
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
over the total working period.
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping their hands warm,
and organising workflows correctly.
English | 11
PSS 300 AE
3 603 C40 3..
W 250
●
-1
min 7000–12,000
-1
min 14000–24,000
mm 1.8
mm 115 x 230
mm 115 x 280
mm 115 x 230
kg 1.9
/ II
1 609 92A 691 | (22.04.2021)