Triton TWX7 CS001 Instrucciones De Uso página 5

6. Check the Riving Knife is aligned with the Saw Blade. If the Riving Knife is not aligned, repeat steps
'3-5' until aligned
7. Replace the Kerf Plate, the Riving Knife is now aligned
Blade guard and accessory installation
Note: Refer to Fig. K, when installing the Blade Guard (3) and Anti-Kickback Device (7).
Note: Ensure the removable Blade Guard is down over the Saw Blade (2) for through-sawing cuts.
• Slot the Blade Guard onto the Riving Knife (5) and fasten into place by turning the Guard Securing Clip (6)
so it is parallel with the Riving Knife
• Slot the Anti-Kickback Device into the mounting point at the rear of the Riving Knife, then fasten into place by
turning the Anti-Kickback Securing Clip (7) so it is parallel with the Riving Knife
Rip fence
• Unfold the Rip Fence Arms (54) and slide into the Rip Fence Guides of the Workcentre chassis, Fig. L
• The Rip Fence Arms display a graduation scale. When used in combination with the Rip Fence Position Indicator,
accurate width measurements can be determined
Protractor gauge
• Loosen the Bench Locking Knob (44) and slide the Bench Rail (51) into the T-Slot of the Workcentre chassis, Fig. M
• Tighten the Bench Locking Knob to secure the Protractor Gauge (43)
• Angle adjustment can be achieved by unlocking the Angle Adjustment Knob (52) and turning the Protractor Gauge
to the desired angle
• The angle is displayed through the Angle Viewfinder (50)
• Adjust the Adjustable Front Fence (45) by loosening the 2 hex bolts, to accommodate different-sized workpieces
• Turn the Protractor Gauge around and set the angle to 0° to use the 45° Angle Fence (47) for a precise 45° cut
Dust extraction
WARNING: ALWAYS use a suitable vacuum cleaner or workshop dust extraction system.
WARNING: Some dust from natural wood, surface coatings and composite materials contain toxic substances.
ALWAYS dispose of harmful dust according to laws and regulations.
• While dust extraction can be achieved using any vacuum cleaner, domestic (bag-type) units can fill up very quickly.
For a much larger capacity, consider fitting a Triton Dust Collector (DCA300) to your vacuum cleaner
• The combined electrical load of the Contractor Saw and vacuum cleaner may exceed the rated amperage of the
domestic extension lead or power outlet. Always connect the vacuum cleaner and Contractor Saw to separate
electrical outlets, and switch on both appliances separately
Electrical connections
Note: The Workcentre features a mains isolator switch with Trailing Socket, to allow easy connectivity to
power tools, Fig. N
Connect the Workcentre to the mains via the Mains Plug
• Use the Trailing Plug to connect power tools to the power supply.
1. Power tools must be connected to the Workcentre switchbox
2. If necessary, suitable extension cords may be used to extend the Workcentre's own power cable
WARNING: Use only extension cords that are in good condition, with a sufficient cross section to carry the current
the power tool will draw. Undersized extensions will cause in-line voltage to drop, resulting in power loss, overheating
and burning out of the power tool motor.
Operation
WARNING: ALWAYS wear eye protection, adequate respiratory and hearing protection, as well as suitable gloves,
when working with this tool.
IMPORTANT: The Contractor Saw Module is marked with the feed direction. This indicates the correct and safest
direction for the workpiece when making the cut.
WARNING: Do not over-balance the Workcentre by using very large workpieces.
WARNING: Ensure the Kerf Plate (27) is installed and levelled correctly before use.
Note: Refer to your original TWX7 Workcentre instructions for full information and diagrams that refer to parts
of the Workcentre.
Workcentre switchbox operation
IMPORTANT: The switchbox requires a live mains connection to switch 'on'. It will reset to 'off as soon as power is
disconnected and require resetting to 'on' when power is restored to continue operation.
Switching ON & OFF
1. The Workcentre ON/OFF Switch is located at the front of the Workcentre chassis, Fig. N
2. Connect the Workcentre Mains Plug to a wall socket and switch 'on'
3. Switch the Workcentre ON/OFF Switch into the 'O' position by pushing on the 'Knee-Off' Stop Button
4. Connect the power tool's mains plug to the Power Tool Connection Socket
5. Switch 'on' the power tool by pressing the ON/OFF Switch into the 'I' position
• Press down on the Knee-Off Stop Button to switch 'OFF'
Note: If the power supply is interrupted during use, the machine will not restart. The ON/OFF Switch will need to be
activated again to resume operation.
User position and feed direction
• The main user position is defined by the location of the Knee-Off Stop Button
• ALWAYS remain positioned in close proximity to the ON/OFF Switch, so the machine can be instantly
switched off in the case of emergency
• Feed workpieces in the direction indicated by the arrows on the Module Table Surface (31)
Using the table extensions (available as accessories)
• The (optional) Workcentre Outfeed Support (TWX7OS) and Workcentre Side Support (TWX7SS) bars can be adjusted
to provide sturdy support to larger workpieces. Adjustability can be performed by loosening the Outfeed Support
Knobs, and/or the Side Support Knobs and extending the corresponding support bar to the size of the workpiece
Adjusting the protractor gauge
Note: In order to increase the life span of the Protractor Gauge (43) it is recommended that a sacrificial piece
of wood should be fixed to the fence.
1. With the Protractor Gauge located in the T-Slot, loosen the Bench Locking Knob (44) and the Angle
Adjustment Knob (52)
2. Adjust the angle of the Protractor Gauge, the angle is displayed through the Angle Viewfinder (50)
3. Lock the Angle Adjustment Knob securely, whilst only securing the Bench Locking Knob until resistance is felt,
to secure the Protractor Gauge in the T-Slot
• Alternatively if a 45° angle is required:
1. Remove the Protractor Gauge and reinstall so the Adjustable Front Fence (45) is trailing
2. Ensure '0°' is displayed through the Angle Viewfinder and lock the Angle Adjustment Knob
3. Use the 45° Angle Fence (47) to secure the workpiece
Push-stick use
WARNING: Performing cuts on small workpieces can be dangerous and will require the use of push-sticks.
• A Push-Stick (40) is included with this product. However, it may be necessary to use more than one push-stick to
safely cut your workpiece
• When ripping small diameter stock it will be necessary to use multiple Push-Sticks in order to secure the work
piece that is in close proximity to the Saw Blade (2)
Cutting operations
WARNING: NEVER handle the part of the workpiece that is near the Saw Blade (2) whilst the blade is in motion
or whilst the power is ON. Doing so may cause the workpiece to be ejected from the machine and could cause
harm to the operator.
WARNING: Keep both hands away from the blade and the cutting path at all times.
WARNING: NEVER attempt to pull the workpiece back during the cutting process; switch the machine off and wait
for the Saw Blade to stop rotating before removing the part-cut specimen.
WARNING: When cutting oversized workpieces that are larger than the width and/or length of the Workcentre
Table Surface, it is necessary to adequately support the workpiece using the (optional) Workcentre Outfeed Support
(TWX7OS) and/or Workcentre Side Support (TWX7SS) which are available from your Triton dealer.
WARNING: Ensure the Workcentre is set up on a stable, flat, and secure surface. Before using the Workcentre ALWAYS
check for stable footing. Using the Workcentre on rough, unsecure terrain is dangerous and could cause serious harm
to the operator.
Performing a cross cut
WARNING: To avoid the cut-off part of the workpiece being thrown, avoid restricting the workpiece using the Rip Fence
(53). Use the Protractor Gauge (43) to support the workpiece during the cutting procedure.
• If the workpiece does not fit within the maximum workpiece dimensions specified within the 'Specification',
adjust the support structures to accommodate the workpiece during the cutting procedure
1. Position the Rip Fence away from the path of the workpiece. Adjust the Protractor Gauge (43) to the desired angle,
and lock into position
2. Position the Saw Blade so the highest point is approximately 3.2mm higher than the top of the workpiece
3. Hold the workpiece firmly against the Protractor Gauge using the hand closest to the blade, and position the other
hand on the part of the workpiece furthest from the Saw Blade for support
4. Switch the Contractor Saw 'on' and allow the Saw Blade to reach the operating speed
5. Whilst using both hands to support the workpiece, as described in 'step 3', slowly feed the workpiece into
the Saw Blade
Note: Before removing the cut-off part of the workpiece, turn the saw 'off' and wait for the blade to stop rotating.
Performing a mitre cut
• If the workpiece does not fit within the maximum workpiece dimensions specified within the 'Specification', adjust
the support structures to accommodate the workpiece during the cutting procedure
1. Adjust the Protractor Gauge (43) to the desired angle. For instructions on Protractor Gauge adjustment and
calibration, see 'Adjusting the protractor gauge'
2. See 'Performing a cross cut' for cutting procedure instructions
Performing a rip cut
WARNING: Ensure the Rip Fence (53) is used when performing rip cuts, performing free-hand cuts is dangerous.
ALWAYS check the fence is securely locked into position before performing cuts.
WARNING: When performing rip cuts and whenever possible, keep hands clear of the Saw Blade (2) and use the
Push-Stick (40) to feed the workpiece if there is less than 6" between the fence and the blade.
WARNING: NEVER attempt to pull the workpiece back during the cutting process. Turn the machine off and wait
for the Saw Blade to stop rotating before removing the part-cut specimen.
• If the workpiece does not fit within the maximum workpiece dimensions specified within the 'Specification',
adjust the support structures to accommodate the workpiece during the cutting procedure
1. Adjust and lock the Rip Fence by closing the Rip Fence Clamps
2. Remove the Protractor Gauge (43)
3. Position the blade so the highest point is approx. 3.2mm higher than the top of the workpiece
4. Hold the workpiece flat on the table and against the Rip Fence. Keep the workpiece at least 25mm away from
the Saw Blade.
5. Switch the Contractor Saw 'on' and allow the Saw Blade to reach the operating speed
6. Whilst holding the workpiece against the fence and flat to the table, slowly feed the workpiece through the Saw
Blade. Maintain an even pushing force until the entire workpiece has passed through the saw blade. Use the
Push-Stick (40) to continue feeding the workpiece through the blade when the trailing edge is less than 6" away
Performing a bevel rip cut
WARNING: When performing a bevel rip cut, always ensure the Rip Fence (53) is on the right hand side of the Saw
Blade (2). The Saw Blade shall never be angled towards Rip Fence.
Note: This operation follows the same procedure as 'Performing a rip cut' except the Saw Blade angle is set to a value
other than '0°'.
• If the workpiece does not fit within the maximum workpiece dimensions specified within the 'Specification', adjust
the support structures to accommodate the workpiece during the cutting procedure
1. Unlock the Locking Lever (21) and the angle of the Saw Blade (2) using the Bevel Angle Adjuster (16)
2. When the desired angle is set, lock the Saw Blade into place using the Locking Lever
3. Follow the cutting procedure as instructed in 'Performing a rip cut'
Performing a bevel cross cut
Note: This operation follows the same procedure as 'Performing a cross cut' except the angle is set to a value
other than '0°'.
• If the workpiece does not fit within the maximum workpiece dimensions specified within the 'Specification',
adjust the support structures to accommodate the workpiece during the cutting procedure
1. Unlock the Locking Lever (21) and adjust the Saw Blade's (2) angle using the Bevel Angle Adjuster (16)
2. When the desired angle is set, lock the adjustment into place using the Locking Lever
3. Follow the cutting procedure as instructed in 'Performing a cross cut'
Performing a slot cut
WARNING: DO NOT stack dado blades with this machine. The contractor table saw does not support using multiple
blades on the Arbor (34).
1. Detach the Blade Guard (3) and the Anti-Kickback Device (8) by twisting the Guard Securing Clip (6) and the
Anti-Kickback Securing Clip (7)
2. Lower the Riving Knife (5) into its slot cutting position, Fig. I
Note: See 'Riving knife installation' for instructions regarding the changing of Riving Knife positioning.
Accessories
• A range of accessories, including Rugged Transit Kit (TWX7RTK), Side Support (TWX7SS) and Outfeed Support
(TWX7OS), is available from your Triton dealer. Spare parts can be purchased from your Triton dealer or online
at www.toolsparesonline.com
GB
5