Triton TWX7 CS001 Instrucciones De Uso página 6

Maintenance
WARNING: ALWAYS disconnect the Workcentre from the power supply, before cleaning, changing accessories,
making adjustments, or carrying out maintenance.
WARNING: ALWAYS wear protective equipment including eye protection and suitable cut-proof gloves when
cleaning or carrying out maintenance.
WARNING: ALWAYS wear suitable cut-proof gloves when handling the Saw Blade (2). Not doing so may result in cuts,
or harm to the operator.
Saw blade replacement
WARNING: The rated speed of the saw blade must be at least equal to the maximum speed marked on the
power tool. Accessories running faster than their rated speed can break and fly apart.
1. Detach the Blade Guard (3) from the Riving Knife (5) by removing the screw securing the guard to the Riving Knife
2. Loosen the hex screw located at the infeed end of the Kerf Plate (27), and use the Kerf Plate Access Hole to
release the plate, Fig. F
3. With the Locking Lever (21) unlocked, raise the Arbor (34) to its maximum height by turning the Blade Height
Winder (15) anticlockwise
4. Lock the Blade Height Winder into position using the Locking Lever
5. Remove the old Saw Blade (2) by securing the Arbor Holder (32) with Multi-Tool 1 (41), whilst simultaneously
removing the Blade Securing Nut (33) with Multi-Tool 2 (42)
6. Install the two halves of the Blade Flange (35) on to the new Saw Blade, then install the blade assembly on to the
Arbor, Fig. O
Note: Ensure the Saw Blade is installed in the correct orientation. The blade direction arrow found on the Saw Blade
should match the direction of the arrow on the Blade Guard.
7. Fasten the new Saw Blade into place by securing the Arbor Holder with the Multi-Tool 1 whilst tightening the
Blade Securing Nut with Multi-Tool 2
8. Reinstall the Kerf Plate and the Blade Guard
Kerf plate replacement
WARNING: When the Contractor Saw is subject to constant use, the kerf plate may deteriorate. The kerf plate must
remain in good condition at all times. Replace if necessary.
1. Detach the Blade Guard (3) from the Riving Knife (5) by removing the screw securing the guard to the Riving Knife
2. Loosen the hex screw located at the infeed end of the Kerf Plate (27), and use the Kerf Plate Access Hole (24)
to release the plate, Fig. F
3. Install the new Kerf Plate and/or Sacrificial Plate (28)
4. Level the Kerf Plate, see 'Kerf plate levelling' for detailed instructions
5. Reinstall the Blade Guard
Cleaning
• Keep your machine clean at all times. Dirt and dust will cause internal parts to wear quickly, and shorten the
machine's service life. Clean the body of your machine with a soft brush or dry cloth. If available, use clean, dry,
compressed air to blow through the ventilation holes
• Never use caustic agents to clean plastic parts. If dry cleaning is not sufficient, a mild detergent on a damp cloth
is recommended
• Water must never come into contact with the tool
• Ensure the tool is thoroughly dry before use
Clearing debris blockages
1. With the tool switched 'off' and disconnected from the power supply. Detach the Blade Guard (3) from the Riving
Knife (5) by removing the screw securing the Blade Guard to the Riving Knife
2. Loosen the hex screw located at the infeed end of the Kerf Plate (27), and use the Kerf Plate Access Hole to
release the plate, Fig. F
3. Remove the Dust Chute Panel (14) and any vacuum connections connected to the Dust Extraction Port (11)
4. Locate and clear the debris blockage
5. Reinstall the Blade Guard, Kerf Plate, Dust Chute Panel and any vacuum connections once the blockage
has been cleared
Lubrication
• Lubricate all moving parts with PTFE spray at regular intervals, especially after heavy use or cleaning
WARNING: DO NOT lubricate with oil or silicone-based maintenance sprays. Lubricant residue will combine with
wood and dust leading to dirt build-up, which may interfere with moving parts and mechanisms. ONLY dry lubricate,
using PTFE spray.
GB
6
Contact
For technical or repair service advice, please contact the helpline on (+44) 1935 382 222
Web: tritontools.com/en-US/Support
Address:
Powerbox
Boundary Way
Lufton Trading Estate
Yeovil, Somerset
BA22 8HZ, United Kingdom
Storage
• Store this tool and its accessories after use in its case, in a dry, secure place out of the reach of children
Disposal
Always adhere to national regulations when disposing of power tools that are no longer functional and are
not viable for repair.
• Do not dispose of power tools, or other waste electrical and electronic equipment (WEEE), with household waste
• Contact your local waste disposal authority for information on the correct way to dispose of power tools