Festool TPE-RS 100 Q Manual De Instrucciones Original/Lista De Piezas De Repuesto página 10

5 Handle
The handle (4) is available as an accessory,
Order No. 486 375.
5.1 Assembley
The handle supplied consists of two halves,
one shoulder pad, two additional grips and a
fastening segment.
Firstly, join the two halves of the handle
together. Put the thinner end (4.7) into the
barrel with the two-pointed prongs (4.1).
Push the nuts through both large holes (Ø
9 mm/4.2) and screw them in with the SW 5
Allen key (4.6). Now from the top of the barrel
push on the additional grips (4.5) and then
the pad (4.4).
Now place the fastening segment onto the
carpet remover gear housing (3.8). Hang the
wire clamps (3.7) to the right and left on the
hooks (3.9) next to the "ABWEISER" and close
the catches from behind (3.5).
Now connect the handle with the fastening
segment. Put the ridges (3.2) into the grooves
(3.3) on the fastening segment. Screw both
sides together with the washer and the Allen
key screw SW 6 (3.5).
5.2 Application
Depending on the size of the operator the ad-
ditional grips and the shoulder pad are placed
on the handle in such a way as to ensure
optimum removal at the best angle.
6 Carpet knife
A blunt carpet knife can easily be re-sharp-
ened, but if this is no longer possible, the
carpet knife (part no. 486 374) must be re-
placed. Undo the four screws (2.1), take of
the distance bushings (2.2), remove the dust
guard (2.4) and take out the old knife (3.3).
Put in the new blade in the reverse order, with
the fl at side of the blade facing upwards. Do
not forget to put back the dust guard as the
motor could become damaged.
7 Maintenance and care
Always remove the mains plug from
the socket before carrying out any
maintenance work.
To ensure adequate circulation of air, the
ventilation slots in the motor housing must
be kept clean and free of obstruction at all
times.
These tools are fi tted with special motor
brushes with an automatic cut-out. When the
brushes are worn down, the power supply is
shut off automatically and the tool comes to
a standstill.
10
All maintenance and repair work
for which it is necessary to open
the motor housing must be carried
out only by an authorized customer-
service workshop.
8 Disposal
Do not throw the power tool in your household
waste! Dispose of the machine, accessories
and packaging at an environmentally-re-
sponsible recycling centre! Observe the valid
national regulations.
EU only: European Directive 2002/96/EC
stipulate that used electric power tools must
be collected separately and disposed of at
an environmentallyresponsible recycling
centre.
9 Warranty
Our equipment is under warranty for at least
12 months with regard to material or pro-
duction faults in accordance with national
legislation. In the EU countries, the warranty
period is 24 months (an invoice or delivery
note is required as proof of purchase). Dam-
age resulting from, in particular, normal wear
and tear, o-verloading, improper handling, or
caused by the user or other damage caused
by not following the operating instructions,
or any fault acknowledged at the time of
purchase, is not covered by the warranty.
Damage caused by the use of non-original
accessories and consumable material (e.g.
sanding pads) is also excluded.
Complaints will only be acknowledged if the
equipment has not been dismantled before
being sent back to the suppliers or to an au-
thorised Festool customer support workshop.
Store the operating instructions, safety notes,
spare parts list and proof of purchase in a safe
place. In addition, the manufacturer's current
warranty conditions apply.
Note
We reserve the right to make changes to the
technical data contained in this information
as a result of ongoing research and develop-
ment work.
REACH for Festool products, their acces-
sories and consumables
REACh is a European Chemical Directive that
came into effect in 2007. As "downstream
users" and product manufacturers, we are
aware of our duty to provide our customers
with information. We have set up the following
website to keep you updated with all the latest
news and provide you with information on all
the materials used in our existing products:
www.festool.com/reach