Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
•
Debris can accumulate anywhere on
the mower, especially on horizontal
surfaces. Additional cleaning may
be necessary when mowing in dry
conditions or when mulching.
•
Fuel leaks/spills, oil leaks/spills and
excess lubrication can also become
collection sites for debris. Immediate
repair and cleaning up oil or fuel spills
can help reduce fire hazards.
•
In addition to cleaning the mower
before operating and storing, do not
attempt to mow unusually tall grass
(10" or higher), dry grass (e.g., pasture)
or piles of dry leaves. Dry grass or
leaves may contact the engine exhaust
and/or build up on the mower deck
presenting a potential fire hazard.
Global Positioning Module (GPM)
Do not attempt to modify or repair the GPM.
Please see an authorized service dealer for
any issues with the GPM.
Troubleshooting
Excessive vibration
1.
Cutting blade loose or unbalanced.
•
Tighten blade and spindle.
2.
Damaged or bent cutting blade.
•
Replace blade.
Uneven cut
1.
Deck not properly leveled.
•
Perform side-to-side
deck adjustment.
2.
Cutting blade dull or damaged.
•
Sharpen or replace cutting blade.
3.
Uneven tire pressure.
•
Check and correct tire pressure in
all four tires.
Mower will not mulch grass
1.
Engine speed too low.
•
Place throttle in FAST
(rabbit) position.
2.
Wet grass.
•
Do not mulch when grass is wet.
3.
Excessively high grass.
•
Mow once at a high cutting height,
then mow again at desired height
or make a narrower cutting swath.
4.
Dull blade.
•
Sharpen or replace blade.
32
S
4 — P
ection
roduct
Engine fails to start
1.
PTO/Blade engaged.
•
Place blade engage lever in
disengaged (OFF) position.
2.
Blown fuse.
•
Replace fuse(s). Replace with same
rating fuse, if necessary.
3.
Parking brake not engaged.
•
Engage parking brake.
4.
See Engine Operator's Manual.
SurePath Auto Steer System
NOTE: SurePath Auto Steer system issues
may be resolved by turning the mower off,
waiting 10 seconds and then turning the
mower back on.
1.
Indicator/Warning Lights do not flash
blue after key is turned on.
•
Check fuses. Replace with same
rating fuse, if necessary.
2.
Indicator/Warning Lights do not go
solid green.
•
Move away from trees and
buildings. Ensure nothing is
blocking the GPM.
3.
Mower is in an open area but Indicator/
Warning Lights stay flashing green.
•
Check for strength of
cellular signal.
•
Verify SurePath Auto Steer
subscription is still active.
•
Check if mower has been
moved out of the state(s) where
SurePath Auto Steer subscription
was activated.
•
Contact an authorized service
dealer if the above items
are resolved.
4.
Indicator/Warning Lights flash yellow
when you press a button.
•
SurePath Auto Steer system is not
ready. Wait for GPS indicator to be
solid green.
5.
GPS indicator is ON but SurePath Auto
Steer Mode will not engage.
•
Resume use in manual mode and
contact an authorized service
dealer to review active faults.
c
are
6.
Indicator/Warning Lights flash red
while system is being used in SurePath
Auto Steer Mode.
•
Move away from trees and
buildings and verify nothing is
blocking the GPM.
•
Check for strength of
cellular signal.
•
Resume use in manual mode and
contact an authorized service
dealer to review active faults.
7.
Indicator/Warning Lights flash red.
•
Resume use in manual mode and
contact an authorized service
dealer to review active faults.
8.
SurePath Auto Steer Mode leaves uncut
areas between mowing passes.
•
Turn Cutting Width knob
counter-clockwise to increase
mowing overlap.
9.
SurePath Auto Steer Mode is
overlapping too much between
mowing passes.
•
Turn Cutting Width knob clockwise
to reduce mowing overlap.
10.
SurePath Auto Steer Mode needs to
be disabled.
•
Remove GPM fuse (labeled F5:GPM
in the fuse box located under
the operator's seat) to disable
SurePath Auto Steer system.
•
Contact an authorized
service dealer.
Publicidad
Capítulos
Tabla de contenido
