Usb Charging Port; Sleep Function; Clock Setup - Lenco DAR-060 Manual Del Usuario

2. If the unit has never been paired with a Bluetooth device before or cannot find the last paired device, the display and
the Bluetooth status indicator will keep on flashing. Turn on the Bluetooth function of your device and enable the
search until "Lenco DAR-060" is found. Select "Lenco DAR-060" on the Bluetooth device to make connection. Enter
the pass code "0000" if required.
3. After successfully paired the unit will display steady "BT AUDIO".
4. You can now start playing music from your smartphone wirelessly to the speaker.
5. You can press the BT PLAY/PAUSE
6. You can press the BT PREVIOUS

Press and hold the PAIR button on the unit will disconnect the current connection and start to search another new
Bluetooth device.
AUX IN
This allows you to connect an external player's sound through your unit.
1. Plug a 3.5mm audio cable (not included) into your external player's line out and the other end into the AUX IN jack.
2. Press the SOURCE button to enter AUX mode. Display shows "AUX"
3. Start your external player to play music.
4. The unit will output the sound.
NOTE: When the AUX mode is used for more than 4 hours, the unit will switch to standby mode. 10 minutes before
entering standby mode you will be notified with "AUTO-OFF" flashing on the display.
To extend the AUX mode you can press CD PLAY/PAUSE.

USB CHARGING PORT

To charge, connect your smartphone to the USB charging port on the front panel of the unit. Use only smartphone which
requires 5V USB power. Charging time may vary for different smartphones.
Note: Charging function may not be supported for all phones.
EQ OPERATION
You can enjoy different EQ sound effect modes. Press the EQUALIZER button will change to different sound effects of
FLAT/CLASSIC/ROCK/POP/JAZZ.
X-BASS
You can also boost the bass effect of the music. Press the X-BASS button will toggle the X-Bass effect between On and
Off.

SLEEP FUNCTION

1. When the unit is switched on, press the SLEEP button repeatedly to select a sleep duration from either sleep off,
90, 80, 70, 60, 50, 40, 30, 20 or 10 minutes.
2. When the sleep timer is zero, the unit will turn off automatically.
3. To cancel the sleep function, press the STANDBY button to turn off the unit. Or press the SLEEP button repeatedly to
select "sleep off".

CLOCK SETUP

1. Turn off the unit in Standby mode.
2. Press the CLOCK SET button to set the clock. It will display "Clock Set".
3. Press the PREVIOUS
4. Press the PREVIOUS
Note:
- The time set may automatically be overriden by the DAB+ or FM station real time information.
- When the unit is turned on in any mode of operation, pressing the CLOCK SET button will display the time on the display
for a few seconds.
TIMER ON/OFF SETUP
1. Turn off the unit in Standby mode.
2. Press and hold the TIMER button to set the timer on/off. It will display "On Timer".
3. Press the PREVIOUS
4. Press the PREVIOUS
confirm. It will display "Off Timer".
5. Press the TIMER button to the next selection.
6. Press the PREVIOUS
7. Press the PREVIOUS
confirm.
8. Press the PREVIOUS
button to confirm.
button to pause or resume the playback.
or BT NEXT
or NEXT button to adjust the hour. Press the CLOCK SET button to confirm.
or NEXT button to adjust the minute. Press the CLOCK SET button to finish the clock set.
or NEXT button to set the on timer hour value. Then press the TIMER button to confirm.
or NEXT button to set the on timer minute value. Then press the TIMER button to
or NEXT button to set the off timer hour value. Then press the TIMER button to confirm.
or NEXT button to set the off timer on minute value. Then press the TIMER button to
or NEXT button to set the timer on source (DISC, DAB, FM). Then press the TIMER
button to search to the previous or next song.
12