Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
EN
B5. ADAPTING MICROWAVE BLOWER FOR
OUTSIDE BACK EXHAUST
6.
Tighten the outer two screws to the top of the micro
wave oven in place against the wall and the top cabi
net.)
Install grease filters. See the Advice & Instructions
7.
packed with the microwave.
C. RECIRCULATING (NON-VENTED DUCTLESS)
INSTALLATION OVERVIEW
C1.
C2. Prepare Top Cabinet
C3. Check Blower Plate
C4. Mount the Microwave Oven
C5. Install or change Charcoal Filter
IMPORTANT NOTES:
blower plate are securely tightened when they
are reinstalled. This will help to prevent excessive
vibration.
routed and secured, and that the wires are not
pinched.
3/8" TO EDGE
along the dotted line.
Trim the rear wall template
12"
NOTE: IT IS VERY IMPORTANT
TO
THE DIRECTIONS
READ AND FOLLOW
INSTRUCTIONS
IN THE INSTALLATION
WITH THIS
BEFORE PROCEEDING
REAR WALL TEMPLATE.
4"
This Rear Wall Template
serves to position the bottom
mounting plate and to locate
the horizontal exhaust
outlet.
that the template is positioned
1. Use a level to check
accurately.
one stud on the left or
2. Locate and mark at least
right side of the centerline.
It is important to use at
least one wood
screw mounted firmly in
a stud to support the weight
of the microwave. Mark
two additional, evenly spaced
locations for the supplied
toggle bolts.
3. Drill holes in the marked
locations. Where there
is
a stud, drill a 3/16" hole
for wood screws. For holes
a stud, drill 5/8" holes for
that do not line up with
toggle bolts.
MOUNTING PLATE
DO NOT INSTALL THE
AT THIS TIME.
from the rear wall.
4. Remove the template
Instruction book for your
5. Review the Installation
installation situation.
para consultar la
Darle vuelta a la hoja
versión en Español.
to align with holes in the
Locate and mark holes
mounting plate.
IMPORTANT:
STUD ON EITHER SIDE
OF
LOCATE AT LEAST ONE
THE CENTERLINE.
FOR 2 ADDITIONAL,
EVENLY
MARK THE LOCATION
IN THE MOUNTING PLATE
SPACED TOGGLE BOLTS
to align with holes in the
AREA.
Locate and mark holes
mounting plate.
LOCATE AT LEAST ONE
IMPORTANT:
STUD ON EITHER SIDE
OF
THE CENTERLINE.
EVENLY
MARK THE LOCATION
FOR 2 ADDITIONAL,
along the dotted line.
SPACED TOGGLE BOLTS
IN THE MOUNTING PLATE
Trim the rear wall template
AREA.
C1. ATTACH THE MOUNTING PLATE TO THE WALL
Attach the plate to the wall using toggle bolts. At least
one wood screw must be used to attach the plate to a wall
stud.
NOTE: If the cabinet depth including the cabinet doors is
more than 13" then the unit must be spaced out
from wall using adequate materials supporting
150 Ibs to allow proper top vent air exhaust/in-
take.
1. Remove the toggle wings from the bolts.
2. Insert the bolts into the mounting plate through the
holes designated to go into drywall and reattach the
toggle wings to
3
4
To use toggle bolts:
Spacing for Toggles
Thickness
Toggle
Mounting
Bolt
Plate
3. Place the mounting plate against the wall and insert
the toggle wings into the holes in the wall to mount the
plate.
NOTE: Before tightening toggle bolts and wood screw,
make sure the bott m of the mounting plate touch the
and that the plate is properly centered under the cabinet.
CAUTION:
tween the back of the mounting plate and the wall.
4. Tighten all bolts. Pull the plate away from the wall to
help tighten the bolts.
Bolt End
18
Publicidad
Tabla de contenido
