Display Messages - DieHard DH110 Manual Del Usuario

8.2 STARTING A BATTERY WITH LOW
VOLTAGE
If the vehicle's battery voltage is too low for
the jump starter to detect that the clamps
are connected, there is a manual start
procedure to enable the jump start function.
1. Make sure the clamps are correctly
connected.
2. Press and hold the
5 seconds. When the display shows
JUMP START READY, the jump starter
is ready for use.
WARNING! This overrides a safety feature.
It will energize the clamps and cause
sparking if they are touched together. If the
clamp connections are reversed, damage
to the unit, battery and possibly the car's
electrical system will occur.
8.3 POWERING A 12V DC DEVICE
(up to 6A)
The power pack is a power source for most
DC accessories that are equipped with a
12V accessory plug.
CAUTION: Do not use the power pack to
run appliances that draw more than 6A DC.
NOTE: Charging while operating a DC
device (light, USB, memory saver) will
extend run time, but will also extend
recharge time. If the load exceeds 1A,
it will discharge the battery.
1. Make sure the device to be powered
is OFF before inserting the 12V DC
accessory plug into the 12V DC outlet.
2. Plug a 12V port adaptor (not included)
into the unit's 12V output port.
3. Plug your device into the 12V adaptor
port and turn on the device (if required).
4. Press the

9. DISPLAY MESSAGES

Messages during recharge:
CHARGING - xx% (Green LED lit) –
Plugged into the AC or DC charger and
internal battery is recharging.
FULLY CHARGED (Green LED pulsing) –
Plugged into the AC outlet and internal
battery is completely charged.
BATTERY TOO HOT TO CHARGE –
Disconnect charger from jump starter and
allow battery to cool down before recharging.
BATTERY TOO COLD TO CHARGE –
The temperature of the internal battery is
too low.
CHARGING-USB ON – The USB function
is in use while the internal battery is
recharging.
button for
button on the unit, twice.
5. When finished, turn off the DC device
(if required) and disconnect the device.
Press any button, to turn on the
display. Then press the
turn off the 12V function.
6. Recharge the power pack immediately
after unplugging the device.
8.4 USING THE USB PORT
The USB port provides up to 2.1A at 5V DC.
1. Press the
2. Plug a USB connector (not included) into
the USB port of the unit.
3. Plug the other (micro) end of the adaptor
into your device. Turn device on, if
necessary.
4. When finished using the USB port, turn
off the device (if necessary) and unplug
the device. Press any button, to turn
on the display. Then press the
twice, to turn off the USB function.
5. Recharge the unit.
NOTE: The USB power will automatically
turn off if not used for 10 minutes.
8.5 USING THE LED LIGHT
1. Press the
• once – for steady light
• twice – for a flashing light
• three times – for an SOS signal
2. When finished using the light, press the
button again, to turn off the light.
8.6 USING A MEMORY SAVER (not included).
The unit can be used with a memory
saver to save the vehicle's on-board
diagnostic computer settings (radio
programs, diagnostic codes, etc.) while
the battery is disconnected from the
vehicle during repair or maintenance.
CHARGING-12V ON – The 12V function
is in use while the internal battery is
recharging.
FULLY CHARGED-USB ON –
The internal battery is fully charged and
the USB is in use.
FULLY CHARGED-12V ON – The internal
battery is fully charged and the 12V port
is in use.
UNPLUG CHARGER – Attempting to
use the jump starter while the unit is
recharging.
CHARGE ABORTED-SEE MANUAL –
Charging cannot be completed normally.
• 8 •
button, to
button on the unit.
button:
button