Sime RS MK II Serie Manual Del Usuario página 51

KEY
1.. Boiler.body
2.. Burner
3.. Burner.manifold
4.. TCB.M5.x.8..
. screw
5.. Aluminium..
. washer.ø.14
6.. Burner.nozzle
2.11 ASSEMBLING THE SKIRT
Proceed.as.follows.to.assemble.the.skirt.(fig..
11):
–. Position.the.front.and.back.supports.of.the.
skirt.base.(1).between.the.feet.on.the.two.
heads.
–. Anchor.the.side.supports.(2).and.(3).to.the.
KEY
. 1. Front.and.rear.skirt.base.support
. 2. Right.skirt.base.support
. 3. Left.skirt.base.support
. 4. Lower.left.side.rear.panel
..5. Upper.right.side.rear.panel
. 6. Front.left.side.panel
..7. Rear.lower.right.side.panel.
front.and.back.of.the.skirt.base.(1)..with.the.
M6.nuts.supplied.
–. Anchor.panel.(4).to.panel.(5).and.panel.(7). .
to.panel.(8)..using.the.connecting.pins.
–. and.panels.(7-8).to.panel.(9).using.connec-
ting. pins,. anchoring. them. together. with.
two.7SP.x.1/2".self-tapping.screws.
–. Assemble.panels.(4).and.(6).on.the.base.(3).
..8. Rear.upper.right.side.panel
..9. Front.right.side.panel
. 1 0. Cover
. 1 1. Lower.front.wall
. 1 2. Upper.front.wall.(cleaning.plate)
. 1 3. Rear.wall
. 1 4. Baseboard
. 1 5. Door
,.anchoring.them.on.connecting.pins..Pro-
ceed.in.the.same.way.to.anchor.panels.(7).
and.(9).to.the.base.(2).
–. Position.the.lower.front.wall.(11).by.fitting.
it.in.between.the.screws.on.the.burner.ma-
nifold. support. brackets. and. the. cast. iron.
body;.anchor.the.walls.to.panels.(6).and.(9).
with.two.7SP.x.1/2".self-tapping.screws.
–. Position.the.upper.front.wall.(12).by.ancho-
ring.it.to.panels.(5-8).and.to.wall.(11).using.
four.7SP.x.1/2".self-tapping.screws.
–. Anchor. the. rear. wall. (13). . to. panels. (4-5).
and.(7-8).using.the.eight.7SP.x..1/2"..self-
tapping.screws.supplied.
–. Assemble.the.baseboard..(14),.anchoring.it.
to.panels.(6).and.(9).using.connecting.pins.
–. Proceed.in.the.same.way.to.anchor.the.up-
per.front.panel.(16).in.place.
Fig..10
–. Assemble.the.cover.(10).and.the.door.(15).
2.12 ASSEMBLING THE GAS
ASSEMBLY
Connect.the.gas.assembly.to.the.burner.ma-
nifold.as.shown.in.fig..12..
The.gas.assembly.may.be.assembled.on.the.
right.or.left.side.of.the.manifold..
. 1 6. Upper.front.panel
NOTE:
The position of rings (6) and (9) may
be inverted, though the ring with the
slit must always be positioned on the
side where the gas assembly exits.
Fig..11
51