Guarantee - TESY HPWH 2.1 260 U02 S Instrucciones De Uso Y Mantenimiento

At the end of the device lifecycle, the user must therefore take the equipment to suitable separate collection
centers for electronic and electro-technical waste, or to return it to the dealer upon purchasing another equivalent
device, at the ratio of one to one.
The adequate separate waste collection relating to the subsequent sending of the discontinued equipment for
recycling, treatment and/or environmentally-compatible disposal, contributes towards avoiding possible negative
effects on both the environment and health; it also encourages the reuse and/or recycling of materials of which
the equipment is made.
The unlawful disposal of the device by the user leads to the application of the administrative penalties foreseen by applicable
legislation.
The main materials that are used in the production of the equipment are as follows:
•
Steel;
•
Magnesium;
•
Plastic;
•
Copper;
•
Aluminum;
•
Polyurethane.

13. GUARANTEE.

In the event that the device needs to undergo repairs under guarantee, we advise you to either contact the dealer from
whom you have purchased the device or our company. The relative addresses are stated in the catalogues/user manuals of
our products as well as on our website. In order to avoid inconveniences, before requesting a repair under guarantee, we
advise you to carefully read.
Guarantee
This guarantee covers the product to which it was attached at the moment of purchase.
This product guarantee covers any material or manufacturing defects for a period of TWO YEARS as from the original
date of purchase.
Guaranty
In the event that during the course of the guarantee period, material or manufacturing defects should be encountered
(at the original date of purchase), we will arrange for the faulty product or its components to be repaired and/or replaced in
conformity with the terms and conditions specified below, at no extra charge as regards the costs of labor and spare parts.
The technical assistance service has the right to replace faulty products or their components with new or overhauled
products. All replaced products and components will become the property of the MANUFACTURING Company.
Conditions
•
Repairs carried out under guarantee will be performed only if the faulty product is delivered within the guarantee
period together with the sales invoice or a purchase receipt (stating the date of purchase, the type of product as well as the
name of the dealer). THE MANUFACTURER has the right to refuse repairs to be carried out under guarantee in the absence
of the above mentioned documents or in the case in which the information contained in such is either incomplete or illegible.
This Guarantee will be terminated in the event that the product model or identification number have been modified, deleted,
removed or made illegible.
•
This Guarantee does not cover the costs and risks associated with the transport of your product to our COMPANY.
•
The following are not covered by this Guarantee:
a)
Periodic maintenance operations as well as the repair or replacement of parts due to wear and tear;
b)
Consumables (components that will predictably require periodic substitution during the useful life of a product, for
example tools, lubricants, filters, etc.).
c)
Damage or faults due to improper operation,
misuse or mistreatment of the product, for purposes other than normal use;
d)
Damage or changes made to the product resulting from:
Misuse, including:
•
Treatments causing damage or physical, aesthetic, or superficial alteration;
•
Incorrect installation or the use of the product for purposes other than those intended or the
•
failure to comply with instructions relating to installation and use;
•
Improper maintenance of the product that is not in conformity with the instructions relating to correct maintenance;
•
Installation or use of the product that is not in conformity with the current technical or safety regulations of the Country
in which the product is installed or used;
•
The condition or faults relating to the systems to which the product is connected or inside which it is incorporated;
•
Repair operations or attempted repair operations carried out by non-authorized personnel;
Adaptations or modifications made to the product without obtaining prior written authorization from the manufacturing
company, the updating of the product exceeding the specifications and the functions described in the instruction manual, or
modifications made to the product in order to make it comply with the national and local safety regulations in countries other
than that for which it was specifically designed and produced;
•
Negligence;
- 5 years for tank provided changing the MG anodes every 2 years,
- 2 years for appliance.
30