Helpful Hints - DeWalt DCS353 Traducido De Las Instrucciones Originales

OPERATION
Instructions for Use

WARNING: Always observe the safety instructions and
applicable regulations.

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.

WARNING: Ensure switch is fully OFF before installing
the battery.
Proper Hand Position (Fig. K)

WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.

WARNING: To reduce the risk of serious personal injury,
ALWAYS hold securely in anticipation of a sudden reaction.
Proper hand position requires one hand on the main
handle 12 .
Instructions for Use (Fig. A, K)
1. Install the battery pack.
2. To turn the tool ON, hold it as shown in Figure K and press
the variable speed trigger
nOTE: The further the trigger switch is depressed the faster
the tool will operate. If in doubt about the proper speed
for your operation, test the performance at low speed and
gradually increase until a comfortable speed is found.
3. To turn the tool OFF, release the variable speed trigger
Lock on/off Button (Fig. L)
The tool can be locked off by fully depressing the lock on/off
button to the left as shown in Figure L.
4
Pushing the lock on/off button
trigger 1 depressed will lock the trigger in the depressed
position. This allows for more comfort and control in extended
use applications.
Pressing the trigger switch again will release the lock out and
the tool will turn off upon release of the trigger.
nOTE: The tool will automatically shut off after operating
for five minutes with the lock‑on button engaged. To restart
the tool, the user will have to release the trigger and repress
lock‑on button.
LED Worklight (Fig. M)
The LED worklight 2 will activate when the trigger is depressed.
It will automatically shut off following a short period of time
once the trigger is released.
Using the Dust Extraction Adaptor with the
Sanding Platen (Fig. P)
1. Attach the dust extraction adaptor
the Dust Extraction Adaptor.
.
1
4 to the left with the
. Refer to Attaching
20
2. Attach the sanding platen
Installing/Removing Accessories.
3. Attach sanding sheet as described under Installing/
Removing Sanding Sheets.
Using the Dust Extraction Adaptor with
Plunge Cutting Accessory (Fig. Q)
1. Attach the dust extraction adaptor. Refer to Attaching the
Dust Extraction Adaptor.
2. Push dust extraction arm
dust extraction adaptor
3. Attach plunge cutting blade as described under Installing/
Removing Accessories.
4. Adjust the dust extraction arm

Helpful Hints

• Always ensure the workpiece is firmly held or clamped to
prevent movement. Any movement of the material may
affect the quality of the cutting or sanding finish.
• Do not start sanding without having the sandpaper
attached to sanding platen.
• Use coarse grit paper to sand rough surfaces, medium grit
for smooth surfaces and fine grit for the finishing surfaces. If
necessary, first make a test run on scrap material.
• Excessive force will reduce the working efficiency and cause
motor overload. Replacing the accessory regularly will
maintain optimum working efficiency.
• Do not allow the sandpaper to wear away, it will damage
the sanding pad.
.
1
• If the tool overheats, especially when used at low speed,
set the speed to maximum and run it with no load for 2–3
minutes to cool the motor. Avoid prolonged usage at very
low speeds. Always keep the blade sharp.
MAINTENANCE
Your power tool has been designed to operate over a long
period of time with a minimum of maintenance. Continuous
satisfactory operation depends upon proper tool care and
regular cleaning.

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
The charger and battery pack are not serviceable.
C
Lubrication
Your power tool requires no additional lubrication.
25 as described under
22 into the lower aperture of the
.
20
for best results.
22
EnGLIsh
37