Maintenance And Service - stayer BPB32 L20 BRUSHLESS Manual De Instrucciones

Greasing the blades (1-2)
The blades must be greased before each use.
1- Follow the steps described in point 3 of the manual to
activate the tool by opening the blades.
2- With the blades open, deactivate the safety switch (6)
leaving it in position O and remove the battery (7).
3- Remove the hexagonal screw (3) by turning
anticlockwise using the hexagonal spanner (9).
4- Apply lubricating oil (10) in the insertion hole of the
hexagonal nut (5) where the screw (3) is inserted.
5- Screw the screw (3) back into position by turning
clockwise.
6- Operate the trigger (4) several times under vacuum to
redistribute the oil correctly.
Note: Do not use too much oil, apply it carefully.
3_USE
CONNECTION
1- Insert a charged battery (7) into the tool.
2- Activate the safety switch (6) by turning it to position I.
The machine will beep twice to indicate that it is activated.
3- Press the trigger (4) twice in succession to unlock the
safety mechanism. The blades will open, leaving the tool
ready for use.
4- Press the trigger (4) once for each cut you wish to
make.
DISCONNECTING
1- Press the trigger (4) for 3 seconds at a time. This will
cause the scissors to close and emit 2 sounds indicating
that it has been locked with the safety system.
2- Deactivate the safety switch (6) by turning it to the O
position. The tool will emit a sound indicating that it has
been deactivated.
3- Disconnect the battery (7) using the disconnect button
(7).
SAFETY LOCK
Even if a battery (7) is connected to the tool with the
blades open and the safety switch (6) in position I for
activation, the tool will not operate until a safety release
is completed.
To reactivate the tool in this situation, press the trigger (4)
twice quickly and then press it once more.
AUTOMATIC SHUT-OFF
If the tool remains switched on for more than 10 minutes
without activity it will go into automatic shutdown mode.
To restart the tool, deactivate the safety switch (6) by
turning it to position O, and then turn it back to position I.
Then press the trigger (4) twice quickly to unlock the tool.
WORKFLOW
With the tool switched on and activated, press the trigger
(4) once for each cut you wish to make.

4_MAINTENANCE AND SERVICE

MAINTENANCE AND CLEANING
Before any work on the machine (e. g., maintenance,
tool change, etc.) as well as during transport and
storage, set the rotational direction switch to the
centre position.Unintentional actuation of the On/Off
switch can lead to injuries.
For safe and proper working, always keep the machine
and ventilation slots clean.
When the battery is no longer operative, please refer to
an authorised aftersales service agent for Stayer power
tools.
If the machine should fail despite the care taken in
manufacturing and testing procedures, repair should be
carried out by an aftersales service centre for Stayer
power tools.
Cleaning the blades (1-2)
1- Follow the steps described in point 3 of the manual to
activate the tool by opening the blades.
2- With the blades open, turn the safety switch (6) to the
O position and remove the battery (7).
3- Use a wire brush to remove any dirt from the blades.
4- Carefully clean the blades using a cloth rag, applying
lubricating oil (10).
Sharpening the blades (1-2)
1- Follow the steps described in point 3 of the manual to
activate the tool by opening the blades.
2- With the blades open, deactivate the safety switch (6)
leaving it in position O and remove the battery (7).
3- Use a flat file (L) to file the cutting edge of the blade
(1 or 2). Sharpen the blade by following the curve of
the blade longitudinally, maintaining the angle of the file
throughout the entire stroke.
L
4- Use a flat file to file the opposite edge of the blade (1
or 2). File the blade by applying light pressure following
the curve of the blade longitudinally while maintaining the
angle of the file throughout. Do not sharpen this side of
the blade too much or the gap between the blades will be
too wide and the blades will lose effectiveness.
- 13 -
es
it
gb
de
fr
p
tr
cz
el