VALBERG WF 1014 B W180C3 Instrucciones De Uso página 16

B B
Using the appliance Utilisation de l'appareil
Add detergent, close the door and set the program
Load the clothes to be washed m the drum and close the door. Add the detergent into the
relevant compartments for the type of program you are going to select, Add detergent as
described in Auto Dosing operation guide.
1. Press the «On/Off' button.
2. Press program selection button to required program, start up and default the program as
«Cotton»
3. Select washing temperature and spin speed by pressing «Temp.»and «Spin» buttons.
4. Press «Prewash» ,»Extra Rinse»,»Time save», «Power Save» button to select additional
functions.
5. After starting the program, display window displays program length (hours: minutes),
washing temperature and additional function options in sequence.
Addition function selection
At standby state, press «Prewash» ,»Extra Rinse»,»Power save», «Time save»button to select
additional function for current program. Select the function , and then corresponding icon
ligbts up. After starting up, program cannot be changed.
Pre-wash
Select the function to conduct pre-wash so as to enhance washing effects and better remove
stains. Tbis function is suitable for heavy dirt clothes.
Power Save
ECO
The Power Save indication lamp is on after the function is selected, and the indication lamp
will be off after the program ends.
The Power Save function is only added under the standby state of its applicable program, that
is, before the program is started. After the program is started, the function cannot be selected.
The actual temperature be reduced by 5°C and the main wash time be reduced after the
function is selected.
Extra Rinse
After set the function of Extra Rinse, the program runs the rinsing process once again before
running the softening, and the total running time of the program increases accordingly.
Time Save
After pressing this function button,the program time will be shortened according to the
setting,and the program time will be increased back to the original setting by pressing the
28 28 EN FR
B B
Using the appliance Utilisation de l'appareil
Time Save button again. After the program starts,the indicator ligbt is always on.
This function is only added under the standby state of its applicable program, that is, before
the program is started. After the program is started, the function cannot be selected.
After tbis function is selected, the determined main washing time will be reduced by 15 mins.
Inlet water warning
If tap is not opened, or water pressure is over low, inlet water fault icon will display, and
display screen will prompt "F01 " to give alarm.
Drainage warning
If the pipe is squeezed, drainage will not be smooth. In case of failing to completely drain for
long time, drainage fault icon will display, and display screen will prompt "F03" to give alarm
Door Lock Icon
After the program starts the Door Lock icon will light up and the door will be locked.
After completing program, door lock unlocks automatically. During pause, if door opening
condition can be met halfway, the door lock will unlock and its indicator light will go out.
When door lock indicator light flashes, door shall not be opened forcibly so as to avoid personal
injury.
Delay End Function
Delay End function allows to run the machine at the consumers' convenience, for example,
at night when electricity is cheaper.
• Only under the standby mode, this button is valid for selecting the reservation time.
• After the reservation function is selected, the time will increase lh when each time the
reservation button is pressed. Before reservation, if the program time does not satisfy the
integral multiple of lh, it shall be completed by pressing the reservation key for the first
time, and then the time increases lh when each time the reservation button is pressed. If the
reservation is selected, before the program runs, the current reservation can be canceled
by turning the button to select other programs.
• The delay time must be longer than the wash program length as the delay time is the time
program will finish. For example: if the selected program time is 02:28, the delay time selected
must be between 03:00 and 24:00.
• When the reservation process is operated, the icon of 'reservation time' will be on. When
the reservation process startup, the icon of 'reservation time' will flash.
29 29 EN FR