Care Of Accessories; Troubleshooting Guide - Kärcher SC 3 Deluxe EasyFix Manual De Instrucciones

Set the device to the current water hardness before us-
ing it in an area with a different water hardness (e.g. af-
ter a move).
Note
Your water board or municipal utilities authority can pro-
vide information on hardness of tap water.
The water hardness setting is stored until a new setting
(e.g. after a move) is made. The device is set to the
highest water hardness (level IV) in the factory. The de-
vice indicates the set water hardness with flash pulses.
Water hardness levels and flash pulses
Hardness °dH mmol/l
range
I Soft 0-7 0-1.3
II Medium 7-14 1.3-2.5
III Hard 14-21 2.5-3.8
IV Very >21 >3.8
hard
Note
The anti-calcification effect of the decalcification car-
tridge is activated as soon as the device is filled with wa-
ter and put into operation. Lime in the water is absorbed
by the granulate in the decalcification cartridge. Addi-
tional descaling is not required.
Note
The granulate in the cartridge can discolour on contact
with water due to the mineral content in the water, which
is no cause for concern and has no negative effects on
the device, cleaning work or the functionality of the car-
tridge.
Note
Do not pause for longer than 15 seconds when setting
as the device will otherwise be set automatically to the
last selected water hardness or the highest water hard-
ness set during initial start-up.
1. Make sure that the device is switched off.
2. Press the ON/OFF button and hold it for 6 seconds.
Illustration K
3. The decalcification cartridge indicator light flashes
and signals the current water hardness setting with
the number of pulses.
4. Press the Reduced steam volume button repeatedly
to set the lower water hardness level.
5. Press the Maximum steam volume button repeated-
ly to set the higher water hardness level.
6. Release the Reduced/Maximum steam volume but-
ton.
The flash pulse for the set water hardness is indicat-
ed.
7. Repeat the process as necessary until the desired
water hardness level has been achieved.
Note
When the steam volume is pressed, the flash pulse for
the water hardness level is not indicated.
8. Press and hold the ON/OFF button for 4 seconds to
save the setting for the water hardness level. The
decalcification cartridge indicator light lights up.

Care of accessories

(Accessories - depending on scope of delivery)
Note
The micro fibre cloths are not suitable for dryer.
16
Number Interval
of flash between
pulses flash
pulses
1x 4 seconds
2x
3x
4x
English
Note
When washing the cloths, observe the instructions on
the washing tag. Do not use any liquid softeners as this
will affect the ability of the cloths to pick up dirt.
1. Wash the floor cleaning cloths and covers at a max.
temperature of 60 °C in the washing machine.

Troubleshooting guide

Malfunctions often have simple causes that you can
remedy yourself using the following overview. When in
doubt, or in the case of malfunctions not mentioned
here, please contact your authorised Customer Service.
WARNING
Risk of electric shock and burns
Trying to eliminate faults while the appliance is connect-
ed to the mains or has not yet cooled down is always
dangerous.
Remove the mains plug.
Allow the appliance to cool down.
The LED strip flashes red
The dry-run protection for the pump is activated.
1. Switch the device off and back on again.
2. Make sure that the decalcification cartridge has
been inserted correctly and there is sufficient water
in the reservoir.
No water in the water reservoir.
1. Top up the water reservoir, see chapter Topping up
the water.
The steam lever cannot be pressed
The steam lever is locked with the child lock.
 Move the child lock forward.
The steam lever is released.
No / little steam although there is water in the reser-
voir
The decalcification cartridge has not been inserted or
has been inserted incorrectly.
 Insert the decalcification cartridge or insert it cor-
rectly.
The decalcification cartridge has been removed while
topping up the water.
 Leave the decalcification cartridge in the device
when topping up.
New decalcification cartridge has been inserted.
 Press and hold the steam lever continuously.
The full steam output is reached after approximately
30 seconds.
Red "Replace decalcification cartridge" indicator
light lights up / flashes
The run time of the decalcification cartridge ends early.
 Insert the new decalcification cartridge and reset the
maintenance indicator, see chapter Replacing the
decalcification cartridge.
The maintenance indicator was not reset after replace-
ment of the decalcification cartridge.
 Press and hold the Maximum steam volume and
Reduced steam volume buttons at the same time
until the "Replace decalcification cartridge" indicator
light goes out after inserting the decalcification car-
tridge, see chapter Replacing the decalcification
cartridge.
The LED strip is in constantly red and no steam al-
though there is water in the reservoir
Run time for the decalcification cartridge has expired
 Insert the new decalcification cartridge and reset the
maintenance indicator, see chapter Replacing the
decalcification cartridge.