Indicator Lights; Work Method; Routine Maintenance - BM2 BIEMMEDUE SUPER Manual De Uso Y Mantenimiento


Ready

No flame

No water

No diesel

No water softener
7.4 Tanks
Fill the tanks with the respective products: diesel (main filler),
detergent (small filler) and water softener through the filler
under the object compartment lid on the cowling. Each tank
has an identification label near the corresponding filler.
7.5 Start up
Open the mains water tap.
Turn the main switch on. The OK light comes on to confirm
that the machine is powered correctly. Hold the wand firmly
and turn the main switch on the appliance to the ON position.
Press the lever on the handgrip a number of times to eliminate
the air present in the circuit. When the jet is constant, set the
thermostat to the required temperature. The first time the
boiler is turned on, it may give off a little smoke caused by the
presence of air in the circuit.
Before turning the machine off, set the thermostat to OFF,
wait until the water has cooled down completely (1 or 2
minutes), then turn the main switch off.

7.6 Work method

Super and Super Plus series high pressure washers are fitted
with a Delayed Total-Stop control which shuts the machine
down a few seconds after the trigger has been released.
When the trigger is pressed again, the machine starts up
The high pressure washer has a "micro-leak
normally.
control" function which shuts the machine down after repeated
start-ups caused by dripping (leaks). If this function trips, the
machine stops. To start it again, turn the main switch to OFF,
then back to ON (reset). The high pressure washer is fitted
with a "no use" function which shuts the machine down after
20 minutes of inactivity. If this function trips, the machine
stops. To start it again, turn the main switch to OFF, then back
to ON (reset). This function can be cut out, but the operation
must be performed by a qualified professional.
7.7 Pressure regulation valve
The pressure regulation valve enables water pressure to be
reduced to a maximum of about 25 bars. When this value is
decreased, the valve reduces the quantity of water to be
heated, allowing the temperature to be increased.
function enables water at temperatures of more than 100°C to
be delivered for short periods (value varies according to
model and flow rate).
temperatures,
manipulating the jet. Important: prolonged use of high
temperatures leads to a rapid accumulation of limescale.
7.8 Washing with detergent
Open the tap on the panel and operate the lever on the
trigger. The pump automatically takes up detergent from the
tank. Spray the surface to be treated, release the lever on the
trigger, then close the detergent tap. Operate the lever on the
trigger again to begin rinsing. N.B.: detergent delivery will
continue for a few seconds after the tap has been closed due
to detergent left in the hoses. Important: do not spray
detergent onto hot surfaces and rinse within the times
recommended by the detergent manufacturer.

7.9 Indicator lights

The indicator light panel provides information on machine
operation and malfunctions.
All the models
OK light




Super Plus models




8

Routine maintenance

IMPORTANT - During routine maintenance, cleaning
and extraordinary maintenance, personal protection
devices provided must be worn.
IMPORTANT - Failure to observe the following safety
rules may cause injury, death or damage to
equipment.
IMPORTANT - All maintenance and cleaning must be
performed with the machine off and the key taken out.
In the case of the internal combustion engine model,
the plug cable must be detached and the motor cold
to avoid burns and fire. Do not allow personnel not
involved in maintenance to approach the machine
8.1 Safety rules for routine maintenance
Routine maintenance involves a series of simple operations to be
performed at regular intervals and according to the manufacturer's
instructions. The Manufacturer has reduced the number and
complexity of routine maintenance operations to enable them to be
This
Important: with such high
great care must
steady green, the machine is ready
fast flashing indicating «micro-leak stop». Rotate
OFF-ON switch for reseting and power on the
machine.
slow flashing indicating «not use for more than 20
minutes». Rotate OFF-ON switch for reseting and
power on the machine.
Slow 5 sec. blinking after switch-on, Indicating
«scheduled maintenance» (set by Distributor). The
machine will be regularly in use after the led turns
off (after 5 sec.).
No flame light: indicates that the flame is not lit.
The machine shuts down. To reset, turn the main
switch OFF then ON again (reset). This function
can be cut out, but the operation must be performed
by a qualified professional.
No water light: indicates an inadequate supply of
water. The machine shuts down. To reset, turn the
main switch OFF then ON again (reset).
No diesel light: indicates that the diesel is about to
run out. The burner goes out, but the machine
continues operating. To reset, top up with diesel.
Water softener light: indicates that the water
softener is about to run out. The machine continues
to operate normally. To reset, top up with fluid.
be taken when