Rupes HR81M Traducción Del Manual De Instrucciones Original página 10

Battery pack level indication
The battery level LED shows the charge level of the batteries changing the colour:
• GREEN: from 100% to 50% batteries charge
• YELLOW: from 50% to 20% batteries charge
• RED: from 20% to 0% batteries charge
• RED BLINKING: 0% battery charge: the tool does not start.
Soft start
The soft start guarantees the motor and battery protection and reduce the risk of injury for the operator.
STARTING UP
Before starting-up the tool ensure that:
- the packaging is complete and does not show signs of having been damaged during storage or transport;
- the tool is complete; check that the number and type of components complies with that reported in this instruction booklet.
ACCESSORIES ASSEMBLY
WARNING: Before (dis)assembling the tool assure that the speed regulation Knob (2) is in OFF position
WARNING: Do not force the screw it could break. The maximum allowed screw force is 2 Nm. To screw use only
a clockwise direction when the tool is positioned as show in a Fig. 4 and Fig. 6 (to unscrew use counterclockwise
direction).
COUNTERWEIGHT
Push the shaft-locking button (6) (Fig. 1) and screw the unit on a tool shaft. Use the provided key to hold a counterweight (Fig.3).
DISC PAD OR BRUSH (provided or optional)
Dual action version (Fig.4): place the disc pad/brush in the red/blue shaft (4) and screw this one on a shaft (holding it with a provided
key). To remove, hold the shaft with a provided key and unscrew.
Rotary version (Fig.5): place the disc pad/brush in a green shaft (4), hold the shaft locking button (6) and screw the disc pad on a
shaft (Fig. 6), To remove, hold the shaft locking button (6) and unscrew.
ACCESSORY ASSEMBLY 291.390
Push the shaft-locking button (6) (Fig. 1) and screw the extension on a tool shaft (Fig.13).
Use only the accessories listed:
• 9.BF3030 – Nylon brush hard
• 9.BF3015 – Nylon brush soft
• 9.BF3000 – Horsehair brush
• 997.001 – Sanding backing Pad ø30
• 995.001 – Polishing backing Pad ø30
BUFFER PAD (Not provided)
CAUTION: Accessories must be rated for at least the speed recommended on the tool-warning label.
Accessories running over rated speed can fly apart and cause injury. Accessory ratings must always be above tool
speed as shown on tool nameplate.
Assemble the buffer pad (3) (Fig. 7) on the velcro surface of the disc pad (4). Press the buffer pad to attach it to the disc pad.
BATTERY PACK (Provided or Optional)
WARNING: Avoid short circuiting the contacts. Avoid mechanical damage of the battery pack. Do not open or
disassemble. Advice on protection against fire and explosion. Keep away from open flames, hot surfaces and
sources of ignition.
Temperature in excess of 45°C reduce the performance of the battery pack. Avoid extended exposure to heat or sunshine. Storage
at room temperature (approx. 20°C) at approx. 20~60% of the nominal capacity. Every six months of storage, charge the battery
pack as normal.
Intended use
The battery pack 9HB125LT/9HB120LT (Fig. 9) is used as the power source for Rupes BIGFOOT iBrid NANO tool HR81M/HR81ML.
Battery pack 9HB125LT/9HB120LT specifications
WARNING: for technical data refer to the label of Battery pack 9HB125LT/9HB120LT.
WARNING: to reduce the risk of injury or explosion, never burn or incinerate a tool's battery pack even if it is
damaged, dead or completely discharged. When burned, toxic fumes and materials are created.
Model Chemistry
9HB125LT Lithium Ion
9HB120LT Lithium Ion
10
Voltage (V) Capacity (Ah)
10.8 2,5
10.8 2,0
Energy (Wh) Weight (kg)
27÷27,75 0.183 ±0.005
21,6 0.183 ±0.005