Starting And Stopping - Rupes HR81M Traducción Del Manual De Instrucciones Original

WARNING: charge Rupes Li-ION Battery pack 9HB125LT/9HB120LT only in the Rupes Li-ION Battery Charger
9HC120LT. Other types of batteries may cause personal injury and damage.
This tool's battery pack and charger are not compatible with NiCd or NiMH systems.
When to charge
Charge your battery tool when convenient for you and your job. The Rupes BIGFOOT iBrid NANO tool Battery pack does not
develop "memory" when charged after only a partial discharge. It is not necessary to run down the battery tool pack before placing
it on the charger. Use the led Battery pack 9HB125LT/9HB120LT level indication on the Rupes BIGFOOT iBrid NANO tool HR81M/
HR81ML to determine when to charge the Rupes Battery pack.
Charge the battery pack 9HB125LT/9HB120LT
The battery pack(s) contained in the kit shall be charger before use. The provided battery is charged <30%. In order to charge
connect the Li-ion battery with a charging station 9HC120LT till the charging is completed.
WARNING: For your personal safety, READ and UNDERSTAND the instruction manual of charging station
9HC120LT before using.
Assemble battery pack 9HB125LT/9HB120LT
WARNING: Before (dis)assembling the tool assure that the speed regulation Knob (2) is in OFF position.
In order to assemble the battery pack push two clips (Fig. 9) at the same time and insert the battery pack in the tool till it is fixed.
In order to disassemble push two clips at the same time and extract the battery from a tool (Fig. 10).
POWER SUPPLY (provided or optional)
WARNING: For your personal safety, READ and UNDERSTAND the instruction manual of Power supply
9HP120LT before using.
Assemble power supply 9HP120LT (10)
WARNING: Before (dis)assembling the tool assure that the speed regulation Knob (2) is in OFF position.
In order to assemble the power supply block push two clips (Fig. 11) at the same time and insert the power supply block in the
tool till it is fixed. In order to disassemble push two clips at the same time and extract the power supply block from a tool (Fig. 12)
BEFORE STARTING THE TOOL
Ensure that :
- the electric system conforms with the characteristics indicated on a label and the power supply cable and plug are in perfect
condition (when the tool is used with the Power Supply 9HP120LT)
- the battery pack is in a perfect condition and is charged (see Battery pack level indication)
- the ON/OFF switch works properly with the Power supply 9HP120LT/battery pack disconnected;
- all the parts of the tool have been assembled in the proper manner and that there are no signs of damage;
- the ventilation slots are not obstructed.

STARTING AND STOPPING

- Starting: rotate the potentiometer knob (2) and set up the speed from 1 to 5 value. Push the switch lever (7) towards the body of
the tool.
- Stopping: release the lever and rotate the potentiometer knob until OFF position.
WARNING: if a case of unusual vibration, or mismatching of the backing pad is present after a start of the tool,
switch-off the tool immediately and eliminate the fault.
FAILURE TO START
If a tool is failed to start, in a case of:
1) the machine is used with a battery – assure that the battery pack is charged (see Battery pack level indication (9)); assure the
battery was inserted correctly;
2) the machine is used with a power supply – check to make sure the prongs on the cord plug are making good contact in the
outlet; check if the current is present in the plug. Also, check for blown fuses or open circuit breakers in the line.
NOISE EMISSION VALUES
Noise emission values determined according to EN 62841-1:
Use ear protection
VIBRATION EMISSION VALUES
Vibration total values a h (triax vector sum) and uncertainty K determined according to EN 62841-1:
3 AXIS VIBRATION LEVEL (a h )
UNCERTAINTY (K)
SOUND PRESSURE LEVEL
SOUND POWER LEVEL
UNCERTAINTY (K)
HR81M
m/s
2
m/s
2
db (A)
db (A)
db (A)
HR81ML
2.50 1.85
0.28 0.20
HR81M / HR81ML
70
80
3
11