Monogram ZDT925SPNSS Manual Del Propietário página 23

TROUBLESHOOTING TIPS
Save time and money! Review the charts on the following pages first and you may not need to call for service.
Problem Possible Cause
Cloudiness Combination of soft water
on glassware and too much detergent
Low performing
phosphate free detergent
Water temperature
entering the dishwasher
exceeds 150°F (66°C)
Suds in the Wrong detergent
tub
Rinse agent was spilled
Detergent Dishes or utensils are
left in blocking the detergent cup
dispenser
cups
Black or Aluminum utensils have
gray marks rubbed against dishes
on dishes
Dishes don't Low inlet water
dry temperature
Rinse agent dispenser is
empty
Max Dry option not selected
Additional drying time is
needed
Control Door may not be completely
panel closed
responded
Water valve may be turned
to inputs but
off
dishwasher
Flood float may be stuck
never filled
with water
Stained tub White film on inside
interior surface— hard water
minerals
Dishwasher Fuse is blown or circuit
won't run breaker is tripped
Power is turned off
Control panel is locked
Possible leak is detected
Proper Start sequence
was not followed
49-4000215 Rev. 3
This is called etching and is permanent. To prevent this from happening, use
less detergent if you have soft water. Wash glassware in the shortest cycle
that will get it clean.
See A white film on glassware, dishware and the interior in this
Troubleshooting section.
This could be etching. Lower the water heater temperature.
Use only high quality automatic dishwasher detergents to avoid sudsing.
Cascade Platinum™ ActionPacs™ or
®
Dishwashing Detergent
dishwashers.
To remove suds from the tub, open the dishwasher and let suds dissipate.
Open the door, press and hold START for 3 seconds, and close the door.
Always wipe up rinse agent spills immediately.
Reposition the dishes, so the water from the lower spray arm can flush the
detergent cup. See Loading the Dishwasher section.
Reposition the tall utensils or heavy silverware that may be keeping the
dispenser cup door from opening. See the Loading the Dishwasher section.
Don't place large bowls or pots directly under detergent dispenser.
Remove marks with a mild, abrasive cleaner.
Make sure inlet water temperature is at least 120°F.
Select Power Dry or Max Dry.
Use Boost Temp option.
Select a higher cycle, such as Sanitize Temp or Intense.
Check the rinse agent dispenser and fill as required.
Select the Max Dry option to improve dry performance.
Allow the fan to run an additional 90 minutes after the Clean light appears.
Note: If you open the door, this fan extension will be cancelled.
Make sure the door is firmly closed.
Make sure water valve (usually located under the sink) is turned on.
Remove Ultra-Fine filter and lightly tap the piece under the ultra fine filter that
looks like a salt shaker. Replace the filter.
Monogram recommends high quality rinse agents such as Cascade
Power Dry™ Rinse Aid or Finish
mineral deposits from forming.
Run dishwasher with citric acid to remove mineral deposits. You can order
citric acid #WD35X151 through Monogram by calling 800-444-1845.
In Canada, call 800-661-1616. Alternatively, purchase Cascade
Dishwasher Cleaner or Finish
directions on the label.
Replace fuse or reset circuit breaker. Remove any other appliances from the
circuit.
In some installations, the power to the dishwasher is provided through a wall
switch, often located next to the disposer switch. Make sure it is on.
Unlock control panel. See the Getting Started section.
Models are equipped with leak detection and the cycle will be cancelled if a leak
is detected. The display will show "LEAK DETECTED". Contact us for service.
See the Using the Dishwasher section.
What To Do
Finish Quantum
®
have been approved for use in all
Jet-Dry Rinse Aid
® ®
Dishwasher Cleaner
®
Automatic
®
Monogram
Platinum™
®
to help prevent hard water
Platinum™
®
and follow the
23