stayer SCR 216 W Manual De Instrucciones página 20

Starting and stopping the machine
Information
The machine is equipped with a safety system to prevent
accidental start-up.
On the SCR216W and SCR315W models, if the locking
button (3) is not pressed beforehand, the machine will
not work even when pressing the start-up button (6). This
allows you to lower the head while the machine remains
off.
On the SCR255CW model, you can start-up the machine
at any time, but it is impossible to lower the head and
expose the blade without first pulling the locking plate (3).
Warnings!
1 Never leave running machine unattended.
2 Never start the machine with locked disk and, before
starting a cut, always wait until the cutting disk has
reached its maximum speed.
3 Before stopping the machine the disk must be clear
and be rotating freely.
Starting with the manual switch
1 On the SCR216W AND SCR315W models, press the
locking button (3)
2 Press switch 6 on the handle to start the motor
Stopping the machine
1
Stop pushing switch 6.
Preparation and types of cuts
Warning!
It is mandatory to carry out any settings with the cable
unplugged.
Warning!
1 Respect the limits regarding the size and material of
the workpiece.
2 Use clamps to fasten the workpiece whenever
possible.
Y
Preparing the cut
To find the desired angle follow the steps: to adjust its
position.
Mitre cutting (X axis = -45° / +45°, Y axis = 90°):
Y
Mitre cutting occurs when the head stays in a vertical
position, perpendicular to the cutting table. The head can
rotate on its axis from -45° to +45°.
To adjust the mitre angle, loosen the selector knob (1) and
Y
pull the mitre angle lock (2).
Pull the knob (1) to rotate the cutting table.
X
X
X
ENGLISH
20
Once you have found the desired cutting angle, release
the lock (2) and tighten the knob (1).
The lower cutting table has an indicator that can be
checked against the scale ruler on the lower table.
Additionally, the lower table can be easily adjusted to
angles of -45° / -30° / -22.5° / -15° / 0° / +15° / +22.5° /
+30° / +45° (these pre-sets may vary by model).
Once the lower table starts to rotate, the table will stop
automatically when it reaches any of the indicated angles,
where it will make a characteristic noise and lock at that
angle until the lower table is set in motion again.
Bevel cutting (X axis = 90°, Y axis = -45° / 0°):
Y
Bevel cutting occurs when the head tilts on its axis and no
longer remains perpendicular to the cutting table.
This tool only allows the head to swing to the left side.
The SCR315W model can tilt to both sides.
Y
You must loosen the locking knobs of the lateral guides
(17) and slide the lateral guides away from the head
before you can tilt it.
Y
To adjust the bevel cut angle, loosen the head tilt screw
(5) and tilt the head to the desired angle. The machine is
set to tilt to -45° by default.
You can use a goniometer to fine-tune the cutting angle
with the help of the scale ruler found at the base of the
head.
Once you have found the bevel cutting angle, retighten
Y
the screw (5).
On the SCR315W model, pull the tilted cutting pin (18) if
you wish to perform cuts with the head tilted to the right.
Y
Once you have chosen the direction of head tilt, retighten
the tilt pin (18).
Compound cutting (X axis = -45° / +45°, Y axis = -45°
/ 0°):
Y
Compound cutting involves a combination of bevel and
mitre cutting angles.
To find your compound cut, follow the steps indicated for
performing bevel and mitre cuts simultaneously.
20
X
X
X
X
X
X