stayer SCR 216 W Manual De Instrucciones página 22

8 Operator exposes his/her hands, body or garment to
the cutting path.
The two main classes of risks entailed by the use of this
machine are contacts with the cutting disk and projections
of particles or cut pieces.
MEASURE FOR PREVENTING MACHINE-
14.
SPECIFIC RISKS
1. Preventing contacts with the cutting disk
1.1 Prevention during the development of the cutting
operation
1
The operator must mandatorily be sufficiently trained
and instructed, and know the present manual in such
a manner that he/she is able to know if a machine
or his/her working environment are suspicious of not
providing a perfect service.
Do not use the machine under these circumstances!
2 Revise any lack of guards or any other component
of the machine. Never use a machine that is not
complete, not in a perfect condition and not correctly
installed. If the machine has been manipulated, lacks
pieces or is in a bad condition, disconnect it, remove it
from the working area, do not use it and send it to the
technical service.
3 Never put your hands or any other part of the body nor
garment upon or below the cutting area of the disk or
within the cutting path of the disk.
4 Fastening the workpiece to be cut shall not be carried
out manually but with the assistance of pushers,
wedgers and clamps warranting a firm fastening of
the workpiece to be cut under any circumstances
(appearance of nods, etc.). By putting this preventive
measure into practice the risk of contact with the disks
during the development of the operation is practically
excluded as it allows hands to remain distanced from
the hazardous area.
5
Always disconnect the machine when leaving it alone.
6 The presence of one or more assistants will be required
for cutting workpieces being longer than 1.5 m.
1.2 Preventing fortuitous contacts with the disk
rotating without load in the resting position
Independently from that the disk, when resting, stays
protected by the safety guards as installed, it is
categorically advised against using the locking switch so
as to guarantee that disk does not rotate without load in
the resting position thereof
1.3 Preventing abrupt falls of the disk due to breakage
of the spring
1 By means of a regular maintenance the machine will
always be in a perfect condition.
2 Check the area and the machine on each working
day and routinely test all movements visually with the
machine disconnected.
3
Check springs and the bearings thereof on each
working, and have them checked periodically by
qualified personnel.
4 Make sure that the head perfectly ascends to its upper
position by the sole action of springs.
ENGLISH
22
5 Check the upper locking system on each working
day by raising the head up to abutment and checking
locking and unlocking by means of button, and have
this periodically checked by qualified personnel.
6 Never expose your hands or any other part of your
body to he cutting path.
7 Never allow the head that holds the disk to remain
in an undetermined position unless the operator is
mandatorily grasping the control grip.
8
For any break between cuttings, however short it
may be, always use the automatic lock of the head
in the upper position by raising the head to the upper
stopper.
9
Each time that the machine remains at rest, leave it in
the lower resting position by placing the head at 90º
vertical and 0º horizontal, protecting by means of the
stationary guard and finally locking it by lowering the
head and pushing button.
2. Preventing projections of the cut workpiece
So as to carry out the cutting of workpieces using a
stopper,
this latter must be foldable or movable. Once the operator
has selected the cutting range and firmly fixed the workpiece
to the table, he/she will remove the stopper so as to prevent
the workpiece as cut from wedging between the stopper and
the disk.
DUST EXTRACTION
15.
All models are prepared for mounting equipment (not
included) for the aspiration of particles generated during
the cutting operation.
The extraction equipment shall be coupled to the particle
outlet nozzle.
GENERAL SAFETY INSTRUCTIONS
16.
WARNING! When using electrical tools, the essential
safety precautions should always be taken to reduce
the risks of fire, electrical shock and personal damages,
including the following.
Read these instructions with attention before using this
product, and store them.
REGULAR CLEANING, MAINTENANCE AND
17.
GREASING
WARNING! .Desenchufar the plug before performing any
adjustment or maintenance comeback.
Cleaning
Clean the machine starting with a brush or with a flat brush
so as to remove sawdust and with a soft cloth.
If compressed air is available, complete cleaning by
blowing with the compressed air pistol.
Maintenance
After each 2,000 hours of use or each two years the
electrical tool must be sent to the official technical service
for maintenance and complete revision.
Before each use, check nuts and joints to detect any
vibration issues and use. If there are gaps take the
machine to service.
22