Product Safety Instructions - Würth ARS 10-1/4 Manual De Instrucciones

OPERATIONAL PRECAUTIONS
GB
GENERAL SAFETY INSTRUCTIONS
1. Consider work area environment. Do not expose tools
to rain. Do not use tools in damp or wet locations Keep
work area clean and well lit. Do not use tools in the
present of flammable liquids or gases.
2. Guard against electric shock. Avoid body contact with
earthed or grounded surfaces.
3. Keep children away. Do not let visitors touch the tools
or extension cord. All visitors should be kept away from
work area.
4. Store idle tools. When not in use, tool should be stored
in a dry locked up place, out of reach of children.
5. Do not force the tool. It will do the job better and safer
at the rate for which it was intended.
6. Stay alert. Watch out what you are doing Use
common sense. Do not operate tool when you are tired.
Check damaged parts. Before further use of the tool,
a guard or other part is damaged should be carefully
checked to determine that it will operate properly and
perform its intended function.
7. Check for alignment of moving parts, blinding of
moving parts, breakage of parts, mounting and any other
condition that may affect its operation.
8. A guard or other parts that is damaged should be
properly repaired or replaced by an authorized service
center unless otherwise indicated in this instruction ma-
nual. Have defective switches replaced by an authorized
service center. Do not use tool if switch does not turn it
on.
9. To ensure the designed operational integrity of power
tools, do not remove installed cover or screws.
10. Use your tool at lower input than specified on the
nameplate, otherwise, the finish may be spoiled and
working efficiency reduced by motor overload.
11. Do not wipe plastic parts with solvent. Sol-
vents such as gasoline, thinner, benzene, carbon
tetrachloride,alcohol, ammonia and oil containing chloric
annex may damage and crack plastic parts. Do not wipe
them with such solvent. Wipe plastic parts with a soft
cloth lightly dampened with soap water.
12. Dress properly. Do not wear loose clothing or jewel-
ry. Contain long hair keep your hair, clothing, and gloves
away from moving parts.
13. Use safety equipment. Always wear eye protection,
non-skid safety shoes, hard hat, or hearing protection.
14. Do not overreach. Proper footing and balance
14
enables better control of the tool in unexpected situations.

PRODUCT SAFETY INSTRUCTIONS

1. Disconnect battery pack from tool or place the main
switch in the locked or off position before making any ad-
justments, changing accessories, or storing the tool. Such
preventative safety measures reduce the risk of starting
the tool accidentally.
2. Remove adjusting keys or wenches before turning
the tool on . A wrench or a key that is left attached to a
rotating part of the tool may result in personal injury.
3. Use clamps or other practical way to secure and
support the work piece to a stable platform. Holding the
work by hand or against your body is unstable and may
lead to a loss of control.
4. Maintain tools with care. Keep cutting tools sharp
and clean. Properly maintained tools, with sharp cutting
edges are less likely to bind and are easier to control.
5. Use only accessories that are recommended by the
manufacturer for your model. Accessories that may be
suitable for one tool may create a risk of injury when
used on another tool.
IMPORTANT SAFETY INSTRUCTIONS
FOR CHARGER & BATTERY PACK
1. Caution To reduce risk of injury, charge only specific
type rechargeable battery packs. Other types of battery
packs may burst causing personal injury and damage
2. Before using charger, read all instructions and cautio-
nary markings on battery packs and chargers.
3. Do not expose charger to rain or snow.
4. To reduce the risk of damage to electric plug and
cord, pull by plug rather than cord when disconnecting
charger.
5. Use of an attachment not recommended or sold by the
charger manufacture may result in a risk of fire, electric
shock, or injury to persons.
6. Make sure cord is located so that it will not be stepped
on, tripped on, tripped over, or otherwise subjected
damage or stress.
7. Do not operate charger with damaged cord or plug.
Replace them immediately.