Folding & Unfolding The Equipment; Console (Fig. E-1); Display Buttons; Remote Control Buttons - Tunturi CARDIO FIT T10 Manual Del Usuario

- Press the circuit breaker to restart the equipment.
- Insert the mains plug into the equipment.
‼ NOTE
• Some circuit breakers used in homes are not rated for high inrush
currents that can occur when a treadmill is first turned on or even
during normal use. If your treadmill is tripping the circuit breaker
(even though it is the proper current rating and the treadmill is
the only appliance on the circuit) but the circuit breaker on the
treadmill itself does not trip, you will need to replace the breaker
with a high inrush type. This is not a warranty defect. This is a
condition we as a manufacture have no ability to control.
Folding & Unfolding the equipment
‼ NOTE
• Before folding or unfolding the equipment, make sure the
remote control is taken out the holder to avoid it from falling out.
• The both clamp levers ( #8) can be pulled out, and freely
repositioned without tightening, or loosen the fixture.
Release the clamp levers ( #8) and turn to adjust the fixation.
Unfolding the equipment (fig. F1)
- A-When being in vertical storage position
- While supporting the treadmill frame, loosen stabilizer frame
fastening knob (#43) on the RH side of the stabilizer frame ( #42) by
turning it in counter-clockwise direction.
- Tilt the mainframe slightly forwards and fold in the stabilizer frame.
- While supporting the treadmill frame, fasten stabilizer frame
fastening knob (#43) on the RH side of the stabilizer frame ( #42) by
turning it in clockwise direction.
- Lower the upright positioned treadmill in the horizontal position.
- B-When being in horizontal storage position�
- Turn both clamps levers ( #8) in the counter-clockwise direction to
loosen the fixation of the handrail.
- Tilt the handrail in the upright position. ( slightly forward angle )
- Turn both clamps levers ( #8) in the clockwise direction to fixate the
fixation�
- Trainer is now in ready-to-use position.
Refer to the illustrations for the correct way of unfolding the
equipment.
Folding the equipment (fig. F2)
- A-When being ready-to-use position
- Turn both clamps levers ( #8) in the counter-clockwise direction to
loosen the fixation.
- Guide the handrail in the downwards horizontal position.
- Turn both clamps levers ( #8) in the clockwise direction to fixate the
fixation of the handrail.
- Trainer is now in horizontal storage position.
- B-When being in horizontal storage position�
- Tilt the treadmill frame in the upright position by lifting it on the
mainframe ( Do not lift the treadmill by holding the handrail ).
- While supporting the treadmill frame, loosen stabilizer frame
fastening knob (#43) on the RH side of the stabilizer frame ( #42) by
turning it in counter-clockwise direction.
- Tilt the mainframe slightly forwards and unfold in the stabilizer
frame�
- While supporting the treadmill frame, fasten stabilizer frame
fastening knob (#43) on the RH side of the stabilizer frame ( #42) by
turning it in clockwise direction.
- Treadmill is now in vertical storage position. .
Refer to the illustrations for the correct way of folding the equipment.

Console (fig. E-1)

⚠ CAUTION
• Keep the console away from direct sunlight.
• Dry the surface of the console when it is covered with drops of
sweat.
• Do not lean on the console.
• Only touch the display with the tip of your finger. Make sure that
your nails or sharp objects do not touch the display.
‼ NOTE
• The console switches to standby mode when the equipment is
not used for 10 minutes�

Display Buttons

Start/ Stop
- Press "Start/ Stop" button to start the selected workout when
treadmill is in stop mode�
After 3 seconds countdown the workout will start at 1.0 km/h.
- Press "Start/ Stop" button to stop the treadmill gradually when
being in workout mode.
Mode
- Cycle between target setting parameters in programming mode.
Select between: target time, target distance or target calories.
Up
- Increases the speed (1.0 ~ 12.0 km/h).
- Pressing once increases the speed 0.1 km/h.
- Pressing and holding for two seconds will increase the speed faster.
- Change values in target programming mode.
Down
- Decreases the speed (1.0 ~ 12.0 km/h).
- Pressing once decreases the speed 0.1 km/h.
- Pressing and holding for two seconds will decrease the speed
faster�
- Change values in target programming mode.

Remote control Buttons

Stop
- Press "Stop" button to stop the treadmill gradually when being in
workout mode.
Start
- Press "Start" button to start the selected workout when treadmill is
in stop mode�
After 3 seconds countdown the workout will start at 1.0 km/h.
+ (plus)
- Increase value when being in target programming mode.
- (min.)
- Decrease value when being in target programming mode.
1 5
English