Timex W217 Manual Del Usuario página 3

The date function advances the date between the hours of 10 PM and 2 AM...
Avoid setting the date during this timeframe... If you attempt to set the date
during this time period, rotate the crown at a very slow rate to avoid damaging
the watch...
DAY / DATE MODELS
TO SET THE TIME:
1... PULL the crown out to the "C" position...
2... TURN the crown either way to the correct time...
3... PUSH in the crown to the "A" position...
TO SET THE DATE:
1... PULL the crown out to the "B" position...
2... TURN the crown either way to the correct date...
3... PUSH in the crown to the "A" position...
TO SET THE DAY:
1... PULL the crown out to the "C" position...
2... TURN the crown either way for full 24 hour cycle to set day...
3... PUSH the crown in to the "A" position...
TO SET THE BILINGUAL DATE:
If your watch is equipped with a bilingual day display, you may select the
desired language by advancing the day display...
1... PULL the crown out to the "C" position...
2... Repeatedly move the time back to 11pm and forward to 4am until you see
the current day displayed in the desired language...
3... PUSH the crown in to the "A" position...
TO SET THE DATE AND 4TH HAND (GMT MODELS)
If your watch is equipped with a GMT function, you may set the 4th center hand
to display a 2nd time zone...
1... PULL the crown out to the "B" position...
2... TURN the crown clockwise to the correct date...
3... TURN the crown counter-clockwise to the correct 4th hand position for the
2nd time zone you are tracking
4... PUSH in the crown to the "A" position...
MOON PHASE MODELS
TO SET TIME:
1... PULL crown all the way out and turn to correct time...
2... Push crown in to restart... For screw-in setting crown, push crown in while
turning CLOCKWISE to tighten...
DATE
A B C
CROWN POSITION
A B C
CROWN POSITION
TO SET "MOON PHASE" FEATURE:
1... Pull crown to "Middle" position (B) and turn CLOCKWISE or
COUNTERCLOCKWISE until correct moon phase appears...
Caution: Wearing or storing the watch with the crown in the "middle" position
will cause damage to the movement... Always return the crown to the normal
position, or if you wish to save the battery life while storing the watch, leave the
crown in the "out" position...
EASY SET ALARM
HOUR MARKER
ALARM SET
TURNING RING
EASY SET ALARM WITH DATE & INDIGLO
1... From the "A" position, PUSH the TIMEKEEPING CROWN in (towards the
watch case) to activate the INDIGLO
dial...
EASY SET ALARM DATE & TIME SETTINGS
TO SET THE DATE:
1... With the TIMEKEEPING CROWN in the "B" position TURN the
TIMEKEEPING CROWN or TURNING RING in either direction to set the date...
TO SET THE TIME:
1... With the TIMEKEEPING CROWN in the "C" position TURN the
TIMEKEEPING CROWN or TURNING RING in either direction to set the time...
EASY SET ALARM SETTINGS
1... Your easy set alarm watch is equipped with two types of alarms:
2... 12-Hour Alarm: rings OR vibrates twice per day at the desired hour and
minute as long as the alarm is activated... (Alarm crown must be in "E"
position...)
3... Hourly Alarm: rings OR vibrates every hour at the desired minute if activated...
(Alarm crown must be in "F" position...)
TO SET THE 12-HOUR ALARM:
1... With the ALARM CROWN in the "D" position, TURN the ALARM CROWN or
TURNING RING in either direction to set the hour and minute alarm markers...
To activate the alarm to ring or vibrate at the desired time, PULL the ALARM
CROWN out to the "E" position... A single beep sound and flash, OR a
vibration will indicate that the 12-Hour Alarm is activated...
2... The alarm will sound and the dial will flash OR vibrate at the desired time
(hour and minute) and will repeat every twelve hours unless the alarm is
deactivated...
NOTE: Alarm is deactivated when the ALARM CROWN is in the "D" position...
If the alarm is not deactivated it will automatically stop ringing after 20 beeps
and flashes OR stop vibrating, and will resume in 12 hours at the indicated time...
TO SET THE HOURLY ALARM:
1... With the ALARM CROWN in the "D" position, TURN the ALARM CROWN or
TURNING RING in either direction to set the minute alarm marker...
2... To activate the alarm to ring or vibrate at the desired minute, PULL the
ALARM CROWN out to the "F" position... Three beeps sound and flash OR a
vibration indicates the Hourly Alarm is activated...
3... The alarm will sound and the dial will flash OR vibrate at the desired minute
and will repeat every hour on the specified minute unless the alarm is
deactivated...
NOTE: Alarm is deactivated when the ALARM CROWN is in the "D" position...
If the alarm is not deactivated it will automatically stop ringing after 20 beeps
and flashes OR stop vibrating, and will resume again in one hour at the
indicated minute...
2
ENGLISH 990-095926-07
MINUTE MARKER
TIMEKEEPING/INDIGLO NIGHT-LIGHT
®
CROWN. PUSH CROWN TO ACTIVATE
THE INDIGLO NIGHT-LIGHT
®
A B C
POSITION
POSITION
ALARM CROWN
PULL CROWN "OUT" TO
ACTIVATE THE ALARM
NIGHT-LIGHT
®
Night-Light and illuminate the watch
®