Inglesina APTICA XT Manual De Instrucciones página 34

form provided on the website: inglesina.com - Warranty and
Assistance section.
HINTS FOR CLEANING AND MAINTAINING THE
PRODUCT
• This product requires regular maintenance by the user.
• Never force any mechanisms or moving parts; in case of
doubt, check the instruction first.
• Do not store the product if it is still wet and do not leave it
in humid environments since mildew may form.
• Store the product in a dry place.
• Protect the product against weather agents, water, rain
or snow; moreover, continuous and prolonged exposure to
sunlight can cause changes in the colour of many materials.
• Should the product be used on the beach, carefully clean
and dry it afterwards in order to remove sand and salt as they
may cause rusting.
• Clean the plastic and metal parts with a damp cloth or with
a mild detergent; do not use solvents, ammonia or benzine.
• Carefully dry metal parts after any contact with water to
prevent the formation of rust.
• Keep all moving parts clean and, if necessary, lubricate
them with light oil.
HINTS FOR CLEANING THE TEXTILE LINING
• It is recommended to wash the lining separately from other
LIST OF COMPONENTS
fig. 1
A APTICA XT CHASSIS
A1 Rear wheels
A2 Front RH wheel assembly / Front LH wheel assembly
B APTICA XT CARRYCOT
B1 Hood lining
B2 Carrycot apron
C STROLLER
C1 Stroller seat
C2 Handrail
C3 Hood
ACCESSORIES
D Feeding bottle holder
E Storage basket
F Muff (if available)
G Rain cover (if available)
INFANT CAR SEAT (if available)
STANDUP (if available)
CHASSIS
OPENING THE CHASSIS STRUCTURE
fig. 2 Holding the lever (A3) down, lift the chassis firmly
until it opens completely.
fig. 3 Caution: make sure that all closing mechanisms
are properly attached on both sides before use.
ASSEMBLING/REMOVING THE REAR WHEELS
fig. 4 Insert the rear wheel (A1) on the rear axle (A3)
and push it into its housing until it clicks correctly into place.
Proceed in the same way for the other wheel.
34
items.
• Periodically revive the fabric parts using a soft clothes
brush.
• Follow the lining washing instructions on the labels.
• Dry the textile lining completely before using or storing it.
• To prevent formation of mildew, it is advisable to air the
carrycot periodically. In particular, separate the textile lining
from the structure and run a dry cloth over the bottom.
INSTRUCTIONS
fig. 5
attached before use.
Should it be necessary, the rear wheels can easily be removed.
fig. 6
(A1).
ASSEMBLING/REMOVING THE FRONT WHEEL ASSEMBLY
fig. 7
LH (left) and can be easily identified by the reference (A5)
stamped at the fastening peg. The same reference (A6) is also
printed on both front chassis supports.
fig. 8
corresponding front chassis support, until it clicks correctly
into place.
fig. 9
kept on the outside helps to identify correct RH and LH
correspondence between wheels and chassis more easily.
fig. 10
attached before use.
Should it be necessary, both front wheel assemblies can
easily be removed.
fig. 11
assembly out from its housing in the support.
CLOSING THE CHASSIS
fig. 12
simultaneously rotate the rear handle (A10) until the chassis
closes completely.
fig. 13
identify and reach the correct closing position.
fig. 14
(A10).
Never lift the chassis by the handlebar.
ADAPTIVE CRUISE
fig. 15
front and rear suspension.
These are the basic configurations suggested, depending on
Handwash in cold water
Do not bleach
Do not tumble dry
Dry flat in shade
Do not iron
Do not dry clean
Do not spin-dry
Caution: make sure that the wheels are properly
Operate the lever (A4) and detach the rear wheel
The front wheel sets are divided into RH (right) and
Insert the front wheel assembly (A2) in the
The hole (A7) on the wheel assembly and always
Caution: make sure that the wheels are properly
Pushing the small button (A8), pull the wheel
To close the chassis, press the button (A9) and
The arrows (A11) on the handle and chassis help to
To transport the closed chassis, use the rear handle
The Aptica XT chassis has independently adjustable