Descargar Imprimir esta página

Flex DD 2G 18.0-EC LD Instrucciones De Funcionamiento Originales página 19

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 41
DD 2G 18.0-EC LD / PD 2G 18.0-EC LD
■ To remove, press the release button and pull
out the battery (see figure C).
CAUTION!
When the device is not in use, protect the
battery contacts. Loose metal parts may short
circuit the contacts; explosion and fire hazard!
Removable belt clip and bit
bracket
■ Remove the battery pack from the tool.
■ Align the hole of the belt clip 11 and bit
bracket 12 with the threaded hole on the
base of the tool (see figure D).
■ Insert the fastening screw and securely
tighten the screw with a screwdriver (not
included).
Strap fixing
■ Strap fixing is provided to attach a wrist
strap (not included) in order to reduce the
chances of dropping your tool. Wrap the
strip around your hand when carrying the
tool (see figure E).
Install and remove bits
CAUTION!
Before carrying out any work on the power
tool, move the direction preselector switch 7
to the middle position.
■ Place the direction selector switch 7 in the
center position to lock the trigger switch 4.
■ Remove the battery pack. Rotate the chuck
2 counterclockwise, as shown in Figure F,
to open the chuck jaws 3.
■ Insert a bit as far as it will go and rotate the
chuck 2 clockwise and securely tighten by
hand. (See figure G)
■ To remove the bit, rotate the chuck 2
counterclockwise to open the chuck jaws 3
and remove the bit.
WARNING
Make sure to insert the drill bit straight into
the chuck jaws. Do not insert the drill bit
into the chuck jaws at an angle and then
tighten the chuck as shown in Figure H This
could cause the drill bit to be thrown from
the tool, resulting in possibly serious personal
injury or damage to the chuck.
WARNING
The bit may be hot after prolonged use. Use
protective gloves when removing the bit from
the tool, or first allow the bit to cool down.
Direction preselection
(see figure I)
CAUTION!
Change the direction of rotation only when
the power tool is stopped.
Move the direction preselector switch 7 to the
required position:
■ Position the direction preselector switch 7
to the far left of the tool to drive screws in
or tighten screws.
■ Position the direction preselector switch to
the far right of the tool to remove screws
or loosen screws.
■ Position the direction preselector switch
in the "OFF" (center-lock) position to help
reduce the possibility of accidental starting
when not in use.
NOTE
The drill driver/hammer drill will not run
unless the direction-of-rotation selector is
engaged fully to the left or to the right.
WARNING!
Battery tools are always in operating
condition. Therefore, the direction
preselector switch should always be locked
in the center position when the tool is not
in use or when carrying it at your side.
Two-speed gear shifter (see
figure J)
The shifter 6 is located on the top of the tool
and allows to switch between gears "1" and "2".
a.
Gear "1" provides higher torque and
slower speeds for heavy-duty work or for
driving screws, drilling large diameter
holes, or tapping threads. Use the mode
"1" for starting holes without a center
punch, drilling metals or plastic, drilling
ceramics, or in applications requiring a
higher torque.
b.
Gear "2" provides lower torque and
faster speeds for hammer drilling (PD 2G
18.0-EC LD only) or lighter drilling work.
The gear "2" speed is more suitable for
drilling wood and wood composites
and for using abrasive and polishing
accessories.
19

Publicidad

loading

Este manual también es adecuado para:

Pd 2g 18.0-ec ld