Publicidad
Idiomas disponibles
Idiomas disponibles
ENGLISH
blade, increasing the risk of the blade overheating
and binding while cutting.
DO NOT use under wet conditions or in presence of
flammable liquids or gases.
DO NOT let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.
DO NOT use under wet conditions or in the presence of
flammable liquids or gases.
DO NOT let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.
● Young children and the infirm. This appliance is not
intended for use by young children or infirm persons
without supervision.
● This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or
mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for
their safety. Children should never be left alone with
this product.
Fitting and removing the battery (Fig. B)
To fit the battery (15), line it up with the receptacle on the
tool. Slide the battery into the receptacle and push until
the battery snaps into place.
To remove the battery, push the release buttons (16) while
at the same time pulling the battery out of the receptacle.
@
Use
WARNING: Let the tool work at its own pace. Do not
overload. This tool can be used in the right hand or
the left hand.
Charging the Battery (Fig. B)
The battery needs to be charged before first use and whenev-
er it fails to produce sufficient power on jobs that were easily
done before. The battery may become warm while charging;
this is normal and does not indicate a problem.
@
WARNING: Do not charge the battery at ambient
temperatures below 10 °C or above 40 °C.
Recommended charging tem perature: approx. 24 °C.
Note: The charger will not charge a battery if the cell
temperature is below approximately 10 °C or above 40 °C.
The battery should be left in the charger and the charger
will begin to charge automatically when the cell tempera-
ture warms up or cools down.
To charge the battery (15), insert it into the charger (24).
The battery will only fit into the charger in one way. Do
not force. Be sure that the battery is fully seated in the
charger.
Plug in the charger and switch on at the mains.
28
(Original instructions)
The charging indicator (25) will blink.
The charge is complete when the charging indicator (25)
switches to continuously on. The charger and the battery can
be left connected indefinitely. The LED will switch on as the
charger occasionally tops up the battery charge.
Charge discharged batteries within 1 week. Battery life will
be greatly diminished if stored in a discharged state.
Leaving the Battery in the Charger
The charger and battery pack can be left connected with the
LED glowing indefinitely. The charger will keep the battery
pack fresh and fully charged.
Charger Diagnostics
If the charger detects a weak or damaged battery, the charg ing
indicator (25) will flash red at a fast rate. Proceed as follows:
Re-insert the battery (15).
If the charging indicators continues flashing red at a fast
rate, use a different battery to determine if the charging
process works properly.
If the replaced battery charges correctly, the original
battery is defective and should be returned to a service
centre for recycling.
If the new battery gives the same indication as the original
battery, take the charger to be tested at an authorised
services centre.
NOTE: It may take as long as 30 minutes to determine that
the battery is defective. If the battery is too hot or too
cold, the LED will alternately blink red, fast and slow, one
fl ash at each speed and repeat.
Attaching and Removing the Blade (Fig. C)
1. Retract lower guard and assemble saw blade (6) and
outer blade clamp washer (11) as shown in Figure C.
2. Depress the spindle lock button (14) while turning the
blade retaining bolt (12) with the hex wrench (17) until the
blade lock engages and the blade stops rotating.
NOTE: Hex wrench is stored on the saw as shown in Figure A.
Tighten the blade retaining bolt securely with the hex wrench.
NOTE: Bolt has a right-handed thread. To loosen, turn
counterclockwise. To tighten, turn clockwise.
NOTE: Never engage the blade lock while the saw is running,
or engage in an effort to stop the tool. Never turn the tool on
while the blade lock is engaged. Serious damage to your saw
will result.
Supporting Large Panels/Securing Workpiece
(Fig. D-G)
Support large panels to minimize the risk of blade pinching
and kickback. Large panels tend to sag under their own
weight as shown in Figure D.
Supports must be placed under the panel on both sides, near
the line of cut and near the edge of the panel (Figure E).
Publicidad
