Intended Use; Technical Data - Parkside PKS 1700 B2 Manual De Instrucciones

4. Intended use

The drag, crosscut and miter saw is designed
to crosscut wood and plastic respective of the
machine's size. The saw is not designed for cutting
fi rewood.
The equipment is to be used only for its prescribed
purpose. Any other use is deemed to be a case of
misuse. The user / operator and not the manufac-
turer will be liable for any damage or injuries of
any kind caused as a result of this.
Please note that our equipment has not been de-
signed for use in commercial, trade or industrial
applications. Our warranty will be voided if the
equipment is used in commercial, trade or indust-
rial businesses or for equivalent purposes.
The equipment is to be operated only with suitable
saw blades. It is prohibited to use any type of
cutting-off wheel.
To use the equipment properly you must also
observe the safety information, the assembly inst-
ructions and the operating instructions to be found
in this manual.
All persons who use and service the equipment
have to be acquainted with this manual and must
be informed about the equipment's potential ha-
zards. It is also imperative to observe the accident
prevention regulations in force in your area. The
same applies for the general rules of health and
safety at work.
The manufacturer will not be liable for any chan-
ges made to the equipment nor for any damage
resulting from such changes. Even when the
equipment is used as prescribed it is still impossi-
ble to eliminate certain residual risk factors. The
following hazards may arise in connection with
the machine's construction and design:
•
Contact with the saw blade in the uncovered
saw zone.
•
Reaching into the running saw blade (cut inju-
ries).
•
Kick-back of workpieces and parts of workpi-
eces.
•
Saw blade fracturing.
•
Catapulting of faulty carbide tips from the
Anl_4300689.indb 65 Anl_4300689.indb 65
GB/MT
saw blade.
•
Damage to hearing if ear-muffs are not used
as necessary.
•
Harmful emissions of wood dust when used in
closed rooms.
•
The product meets the requirements of EN
61000-3-1 1 and is subject to special con-
nection conditions. This means that use of the
product at any freely selectable connection
point is not allowed.
•
Given unfavorable conditions in the power
supply the product can cause the voltage to
fluctuate temporarily.
•
The product is exclusively intended for use
at connection points that have a continuous
current-carrying capacity of at least 100 A
per phase.
•
As the user, you are required to ensure, in
consultation with your electric power compa-
ny if necessary, that the connection point at
which you wish to operate the product meets
the specified requirements.

5. Technical data

AC motor: .........................................230V ~ 50Hz
Power: ........................................................ 1700 W
Operating mode: ................................................ S1
Idle speed n : ...................................... 4,800 min
0
Carbide saw blade: ...........ø 210 x ø 30 x 2.8 mm
Number of teeth: .................................................. 24
Swiveling range: ........................ -45° / 0°/ +45°
Miter cut: ................................. 0° to 45° to the left
Saw width at 90°: ............................ 205 x 65 mm
Saw width at 45°: .............................140 x 65 mm
Saw width at 2 x 45°
(double miter cut): ..............................140 x 40 mm
Protection class: ..............................................II /
Weight: ..............................................approx. 15 kg
Laser class: ............................................................. 2
Wavelength of laser: .................................. 650 nm
Laser output: .................................................≤ 1mW
Laser module power
supply: ................................ 2 x 1.5 V Micro (AAA)
- 65 -
-1
10.10.12 18:58 10.10.12 18:58