Publicidad
Idiomas disponibles
Idiomas disponibles
protection is activated (see above)
•
Holding and guiding the tool y
! while working, always hold the tool at the grey-
coloured grip area(s)
- always use auxiliary handle J (can be adjusted as
illustrated) u
- keep ventilation slots F2 uncovered
- do not apply too much pressure on the tool; let the tool
do the work for you
•
Adjusting drilling depth i
APPLICATION ADVICE
•
Use the appropriate bits o
! only use sharp bits
•
For drilling with non SDS drill bits in wood, metal and
plastic, use an adapter (not standard included) p
! clean and lightly lubricate the SDS+ accessory
before insertion
- pull back locking sleeve D and insert adapter in SDS+
chuck while turning and pushing it until it engages; the
adapter locks in position automatically
- pull adapter to check whether is it locked correctly
- set switch C to normal drilling (only activate when tool
is switched off and the switch is locked)
•
When drilling ferrous metals
- pre-drill a smaller hole, when a large hole is required
- lubricate drill bit occasionally with oil
•
When turning in a screw at/near the cross cut end or an
edge of wood, pre-drill a hole in order to avoid cracking
of the wood
•
Splinterfree drilling in wood a
•
Dustfree drilling in walls s
•
Dustfree drilling in ceilings d
•
Drilling in tiles without skidding f
•
For more information see www.skil.com
MAINTENANCE/SERVICE
•
This tool is not intended for professional use
•
Always keep tool clean (especially ventilation slots F2)
! remove battery from tool before cleaning
•
If the tool should fail despite the care taken in
manufacturing and testing procedures, repair should
be carried out by an after-sales service centre for SKIL
power tools
- send the tool undismantled together with proof of
purchase to your dealer or the nearest SKIL service
station (addresses as well as the service diagram of
the tool are listed on www.skil.com)
•
Be aware that damage due to overload or improper
handling of the tool will be excluded from the warranty
(for the SKIL warranty conditions see www.skil.com or
ask your dealer)
ENVIRONMENT
Only for EU countries
•
Do not dispose of electric tools, accessories and
packaging together with household waste material
- in observance of European Directive 2012/19/EC
on waste of electric and electronic equipment and
its implementation in accordance with national law,
electric tools that have reached the end of their life
must be collected separately and returned to an
environmentally compatible recycling facility
- symbol 6 will remind you of this when the need for
disposing occurs
! prior to disposal protect battery terminals with
heavy tape to prevent short-circuit
Only for UK
•
Do not dispose of electric tools, accessories and
packaging together with household waste material
- in observance of on Waste Electric and Electronic
Equipment Regulations 2013 (SI 2013/3113), electric
tools that have reached the end of their life must be
collected separately and returned to an environmentally
compatible recycling facility
- symbol 6 will remind you of this when the need for
disposing occurs
! prior to disposal protect battery terminals with
heavy tape to prevent short-circuit
NOISE / VIBRATION
•
Measured in accordance with EN 62841 the sound
pressure level of this tool is 93.4 dB(A) and the sound
power level 104.4 dB(A) (uncertainty K = 3 dB), and the
vibrationÞ (triax vector sum; uncertainty K = 1.5 m/s
when hammer drilling in concrete 16.2 m/s
✱
when chiseling 12.8 m/s
✱
•
The vibration emission level has been measured in
accordance with a standardized test given in EN 62841;
it may be used to compare one tool with another and as
a preliminary assessment of exposure to vibration when
using the tool for the applications mentioned
- using the tool for different applications, or with different
or poorly maintained accessories, may significantly
increase the exposure level
- the times when the tool is switched off or when it is
running but not actually doing the job, may significantly
reduce the exposure level
! protect yourself against the effects of vibration by
maintaining the tool and its accessories, keeping
your hands warm, and organizing your work
patterns
b
Marteau perforateur
sans fil et sans corde
INTRODUCTION
•
Cet outil est conçu pour les travaux de martelage dans
la brique, le béton et dans la pierre naturelle ainsi que
le perçage dans le bois, le métal, la céramique et les
matières plastiques ; les outils avec réglage électronique
de la vitesse et rotation à droite/à gauche sont
également appropriés pour le vissage et le filetage
•
Le système martelage de cet outil surpasse largement la
performance des perceuses à percussion traditionnelles
lorsqu'il est utilisé dans le béton
•
Cet outil convient parfaitement pour une utilisation avec
tous les accessoires SDS+ standards
•
Cet outil n'est pas conçu pour un usage professionnel
•
Lorsque des pièces manquent ou sont endommagées,
veuillez contacter votre distributeur
•
Lisez attentivement ce manuel d'instructions avant
13
)
2
2
2
3851
Publicidad
