Makita DCU603 Manual De Instrucciones página 21

5. As the loads become less stable on slopes,
firmly secure the loads with ropes.
6 . As the machine becomes unstable depending
on the condition of the road, keep the load to a
minimum.
7. As the view is obscured on slopes, keep the
height of the load to a minimum.
8. Never stop the machine on slopes. Stop the
machine on flat ground, and lock the brake
lever, and then turn the power off.
Do not change the direction or speed mode on
9.
steep slopes.
1 0. Do not release the switch trigger on upward
slopes. T h e m a c h i n e m a y g o i n r e v e r s e a n d
c a u s e a n a c c i d e n t .
1 1 . Make sure that the remaining battery capacity
is enough before operating on slopes. If the
remaining battery capacity is not enough,
charge the battery or replace it with a charged
one.
1 2. When starting the machine on slopes, do not
place your foot behind the rear wheel since the
machine moves back a few centimeters.
Loading objects
1 . Do not overload objects. When loading
objects, be sure to follow the instructions and
load limits in the manual.
2. Since the larger the load, the more difficult it
is to operate the machine, keep the load within
the range that does not affect the operation.
Firmly secure the objects with ropes.
3.
4 . Load the objects within the carrier, bucket,
or flat bucket. If the objects protrude from the
carrier, bucket, or flat bucket, there is a risk of
accidents due to the objects falling or contact
o b s t a c l e s s u c h a s w a l l s .
Be sure that loaded objects are below eye
5.
level. I f t h e l o a d i s t o o h i g h , i t i s d a n g e r o u s
b e c a u s e t h e v i e w i s o b s c u r e d . A l s o , t h e r e i s a r i s k
of overturning and injury because the load is likely
t o b e u n b a l a n c e d .
6 . Load the objects on the carrier, bucket, or flat
bucket evenly. If the objects are loaded unevenly,
there is a risk of overturning and injury because
t h e l o a d i s l i k e l y t o b e u n b a l a n c e d .
7. Before loading the objects or operating the
machine, make sure that the handle of the
dump unit is fully pulled down and completely
locked.
8. Be sure to load heavy objects first to keep
balance.
9. Do not extend the front and side rails on steep
slopes. Extend the side rails when lightweight
objects are loaded.
1 0. When extending the front and side rails, do not
extend them over the extension limit. Be sure
to extend the side rails so that the right and
left sides are the same length, and load objects
evenly.
1 1 . Load and unload objects on flat ground. Never
load or unload objects on slope.
1 2. When lifting and tilting the carrier or bucket,
hold the handles and frame firmly, and work in
a stable posture.
1 3. When loading liquids, be careful not to spill
them. S p i l l i n g t h e m
an injury.
Transportation of machine
1 . Use the ladder rails that are at least 4 times
as long as the height of the truck bed, with
fixtures suitable for the bed, with a non-slip
surface and sufficient width, and capable of
withstanding the weight of the machine and
operator. Read the instruction manual of the
ladder rails carefully before use.
Before loading the machine, unload all objects
2.
from the machine and remove mud and other
debris from the tires. Install the ladder rails on
a flat and stable surface.
3. Before loading or unloading the machine,
make sure that there are no people around the
machine and the ladder rails. Load or unload
the machine at low speed, taking care to pre-
vent the machine from falling off the ladder
rails, and not to hit your head on the ceiling of
the truck. Use extreme caution when loading
or unloading the machine backward.
When transporting the machine, lock the brake
4 .
lever, turn the power off, remove the batteries
and lock key, and fix the machine securely.
Maintenance and storage
Before storage or attempting to perform
1 .
inspections or maintenance, always be sure
to stop the machine on flat ground and lock
the brake lever, and turn off the machine, and
remove the lock key and battery cartridges.
2. Do not leave the machine unattended outdoors
in the rain.
3. When storing the machine, avoid direct sun-
light and rain, and store it in a place where it
does not get hot or humid.
Battery tool use and care
1 . Recharge only with the charger specified by
the manufacturer. A c h a r g e r t h a t i s s u i t a b l e f o r
one type of battery pack may create a risk of fire
w h e n u s e d w i t h a n o t h e r b a t t e r y p a c k .
2. Use power tools only with specifically desig-
nated battery packs. U s e o f a n y o t h e r b a t t e r y
packs may create a risk of injury and fire.
3. When battery pack is not in use, keep it away
from other metal objects, like paper clips,
coins, keys, nails, screws or other small metal
objects, that can make a connection from one
terminal to another. S h o r t i n g t h e b a t t e r y t e r m i -
nals together may cause burns or a fire.
4 . Under abusive conditions, liquid may be
ejected from the battery ; avoid contact. If con-
tact accidentally occurs, flush with water. If
liquid contacts eyes, additionally seek medical
help. Liquid ejected from the battery may cause
i r r i t a t i o n o r b u r n s .
5. Do not use a battery pack or tool that is dam-
aged or modified. Damaged or modified batteries
m a y e x h i b i t u n p r e d i c t a b l e b e h a v i o u r r e s u l t i n g i n
fire, explosion or risk of injury.
6 . Do not expose a battery pack or tool to fire or
excessive temperature. Exposure to fire or tem-
p e r a t u r e a b o v e 1 30 ° C m a y c a u s e e x p l o s i o n .
21 ENGLISH
m a y c a u s e s l i p p i n g a n d c a u s e