Publicidad
Idiomas disponibles
Idiomas disponibles
Always store the device in a clean and well-serviced state in a closed,
dry room and inaccessible to children.
Before storing the machine, always remove the battery and the safety
key in order to prevent unauthorised operation of the machine.
For reasons of warranty and safety, only genuine spare parts may be used.
Non-equivalent spare parts can damage the machine and are a safety hazard.
7 DESCRIPTION OF COMPONENTS
1
Operating clamp for engine (safety control bar)
2
Ejection flap
3
Battery (under the battery cover)
4
Safety key (under the battery cover)
5
Battery cover
6
Engine hood
7
Cutting height notches
8
Adjusting handle for cutting height adjustment
9
Start button (red)
8 PREPARATION
The following parts are included in the packaging for assembly of the mower:
•
Mower with preassembled guide bar
•
Collector sheet, grass collector frame
•
Tool bag with the following contents:
–
Operating instructions with declaration of conformity
–
Warranty conditions (depending on model)
–
Various fixing parts.
•
Mulch plug (only 45-ACCU CLASSIC)
In the unlikely event of a missing part, please contact your dealer.
Raise the guide bar (figure A1 + O4 + B1 )
IMPORTANT
Make sure that the cables are not pinched, squeezed, twisted or overstretched
when the guide bars are folded apart or collapsed! Always run the cables along
the outside of the bar connection. A damaged cable may result in a technical
defect of the device.
Open out the Z-shaped, folded guide bar by pulling upwards in the following order:
–
First, lift up the lower guide bar section A1, push the lower part ends so far apart
that the locking cams pointing inwards on both sides lock into the corresponding
bores B1.
Three different handlebar heights can be set.
To set a different bar height, the wing nuts must be removed, the screws
must be pulled out completely and inserted into the corresponding rectangular
holes. The holes and bores for the lowest and highest height adjustment are
in each case one level above the holes and bores of the medium height
adjustment.
Caution: After the screws have been pulled out, the handlebar can turn over
unintentionally.
–
Manually tighten the wing nuts on both sides B1.
–
Lift the upper guide bar section until upper and lower section of the guide bar are
at one level.
(Figure O4)
–
When the upper and lower section of the guide bar are at one level, tighten the
wing nuts manually.
–
Insert the cable into the cable guide and use the cable ties from the tool bag to
help you attach it to the upper and lower parts of the guide bar. Lay the cable on
the outside of the bar so that the ejection flap can move freely when you raise
and close it.
When collapsing the upper part of the bar, ensure that the cable is freely
accessible.
CAUTION
When operating the bar height adjustment, the bar may turn over
unintentionally when loosening the wing nuts B1 to fasten the lower bar
section at the housing and disengaging the locking cams from the bores in the
housing. In addition, there may be pinching points between lower bar section
and housing. This may result in risk of injury!
Assembling the grass collecting bag and attaching it to the mower
(figure R1 + S1 )
–
Insert the grass collector frame into the collector sheet with the bar to the front.
Align the top seam of the collector sheet with the bar.
–
Press the retaining profiles onto the frame of the grass collector frame R1 .
–
Open the ejection flap of the mower upwards.
–
Pick up the grass collecting bag by the carrying strap and hang in the grass
collecting bag at the top of the mower housing with its two side hooks S1 .
–
Attach the ejection flap to the collecting bag.
Adjusting the cutting height (figure I )
Safety information!
For explanation of symbols, see the table on page 2
Your desired cutting height is set with the one-hand adjusting lever (1) on the right
side of the mower.
-
Bend the lever so far from the housing that the locking cam disengages from the
bore and engages again in the desired position after lateral rotation.
IMPORTANT
You should only use your mower at the lowest cutting height on even and flat
lawn surfaces! Please note that the lower cutting height settings are only to be
used under optimum conditions. If your selected cutting height is too low,
the sward may be damaged and even destroyed.
In addition to the cutting height, the driving speed also influences the cutting
pattern and the collection result. Adjust the cutting height and the driving speed
to the grass height to be cut.
Inserting the charged battery (figure K2 + V1 + G2 )
The handling of the charger and battery is described
in the separate operating manual for the charger.
In particular, read and follow the safety information!
Charge the battery fully before initial use!
–
Open the battery cover and hold it open.
–
Remove the safety key K2 .
–
Push the battery into the battery compartment until the lock engages V1 .
Ensure that the lock on the battery moves freely and engages cleanly.
–
Insert the safety key if the machine is being used immediately G2 .
–
Close the battery cover. Ensure that the cover closes automatically. Dirt and
grass residue can prevent this and must therefore be removed.
9
Publicidad
