Publicidad
Idiomas disponibles
Idiomas disponibles
Regrinding and balancing of the cutter bar (figure Q )
WARNING
The regrinding and balancing of the cutter bar must be carried out by an
authorised workshop. An incorrectly ground and unbalanced blade can cause
strong vibrations and damage the lawn mower.
The cutting edges of the cutter bar may only be reground until the marking (1) on the
cutter bar (ring) (see figure Q) has been reached. Attention! Observe the grinding
angle of 30°.
Your workshop can check this value (wear limit) for you!
WARNING
A blade in which the wear limit (marking) has been exceeded may break and be
thrown away, which can lead to serious injuries.
Changing the cutter bar
WARNING
The replacing of the cutter bar must be carried out by an authorised workshop.
Due to an incorrectly assembled blade fastening or an excessively or
insufficiently tightened blade screw, the cutter bar may become loose, which
can lead to serious injuries.
–
For replacement, use only original cutter bars. Non-equivalent spare parts can
damage the machine and are a safety hazard.
–
Replacement cutter bars must be permanently marked with the name and/or
company logo of the manufacturer or supplier and the part number.
Servicing the wheels (figure S )
Lubricate the wheel bearings once a year or every 15-20 operating hours.
–
Remove the wheel caps S .
–
Using a wrench, loosen the hexagonal nut and remove the pulley and the wheels.
–
After the bearings have been lubricated with roller bearing grease "KAJO-
Langzeitfett LZR 2", push the wheels back in place, attach the washer, fasten
using the hexagonal nut and tighten so that the wheels can turn easily but without
play. Reattach the wheel cap.
Customer service
Our customer service is offered by an authorised dealer. You can find a specialised
dealership on our homepage at www.sabo-online.com and under the "Service" /
"Search Specialist" tab. If you are unsure, please contact your sales partner.
17 TROUBLESHOOTING
Faults
Possible causes
Safety key not inserted.
Engine does not start
Battery not charged.
Battery not functional or
cannot be charged.
Cutting height set too low
(when the grass is too
high, this prevents the
engine from starting up).
Too much grass waste in
the housing or ejection
channel.
The battery charge level
An
acoustic
signal
is below 10%.
sounds
Battery not functional or
cannot be charged.
The
acoustic
sounds even though the
battery
technical defect on the
mower
Remedy
Insert the safety key G2 .
Charge the battery (see the
separate
operating
instructions for the charger).
Replace the battery.
Set a higher cutting height I .
Tilt
the
machine
starting.
Clean grass out of the cutting
space / ejection channel, keep
the gap between the fan and
housing clean (remove the
safety key first K2 !).
Have it checked by an
authorised workshop.
Charge the battery (see the
separate
operating
instructions for the charger).
Replace the battery.
signal
Have it checked by an
authorised workshop.
is
charged:
Engine switches off
during mowing
Engine power
decreasing
Extreme vibration
Poor cutting,
lawn turns yellow
Ejection blocked
The
mulched
grass
looks bad:
lumps,
excessive
amounts of cut grass,
coarse cut
when
In case of faults and defects which have not been listed here, please contact the
nearest authorised workshop.
Repairs which require specialised knowledge should only be performed by a qualified
expert. Your authorised workshop will naturally also be glad to help if you do not wish
to perform the maintenance work described here yourself.
13
Cutting height too low.
Set a higher cutting height I .
Battery is drained.
Charge the battery (see the
separate
instructions for the charger).
Too much grass waste in
Clean grass out of the cutting
the housing or ejection
space / ejection channel,
keep the gap between the fan
channel.
and housing clean (remove
the safety key first K2 !).
Cutter bar blunt.
Have
it
balanced by an authorised
workshop Q .
Battery capacity low.
Charge the battery (see the
separate
instructions for the charger).
Too much grass waste in
Clean grass out of the cutting
the housing or ejection
space / ejection channel, keep
channel.
the gap between the fan and
housing clean (remove the
safety key first K2 !).
Have it checked by an
authorised workshop.
Cutter bar blunt.
Have
it
balanced by an authorised
workshop Q .
Cutting height too low.
Set a higher cutting height I .
Excessive
mowing
Adapt mowing speed.
speed.
Mower paths do not
With high grass, the mowing
paths may possibly have to
overlap sufficiently.
overlap more.
Lawn matted.
A noticeable improvement
can be achieved by using a
scarifier.
Collecting bag full.
Empty the collecting bag L .
Cutting height too low
Set a higher cutting height I .
and grass too high.
Excessive
mowing
Adapt mowing speed.
speed.
Grass is wet.
Let lawn dry.
Cutter bar blunt.
Have
it
balanced by an authorised
workshop.
Mulching
rule
not
Set a higher cutting height I .
followed (cut max. 1/3 of
grass height; the grass
height to be cut must be
less than 10 cm).
Excessive travel speed.
Adapt travel speed.
Grass
accumulation
Set a higher cutting height I .
under the mower.
Mower paths do not
With high grass, the mowing
overlap sufficiently.
paths may possibly have to
overlap more.
Grass is wet.
Set a higher cutting height I .
Let lawn dry.
operating
reground
and
operating
reground
and
reground
and
Publicidad
