Sony STR-AZ1000ES Guia De Instalacion página 13

Calibration Matching
When Auto Calibration is executed, this function works
automatically to match the phase of the right and left
speakers. You can set this function only after the D.C.A.C. IX
measurement process has been completed and the results
of D.C.A.C. IX measurement are saved. The setting is valid
until you change it.
Note
• If an error code or warning message appears on the screen in
step 3, see "List of messages after Auto Calibration measurements"
(page 13).
Tips
• You can also perform automatic calibration by pressing the
AUTO CAL. button on the remote control. If you use the AUTO CAL.
button, the following restrictions apply to the operation:
– Prior settings relating to the Auto Calibration will be skipped.
– You can only use the display panel for the operation.
• The Auto Calibration function will be canceled if you perform the
following during the measurement process:
– Turn the receiver on or off.
– Press the input buttons on the remote control or turn
INPUT SELECTOR on the receiver.
– Press  (muting).
– Press SPEAKERS on the receiver.
– Connect your BLUETOOTH® headphones/speakers.
– Press HDMI OUT.
– Press AMP MENU.
– Press HOME.
– Press BACK.
– Change the volume level.
– Connect the headphones.
List of messages after Auto Calibration
measurements
• Error 30:
Headphones inserted. Remove headphones and
remeasure.
• Error 31:
SPEAKERS(A/B/A+B/OFF) are off. Re-measure with audio
coming out of the SPEAKERS (A/B/A+B/OFF).
• Error 32:
No sound was detected from any channel. Is the
measurement microphone damaged? Is it connected to
the CALIBRATION MIC jack on the front of this unit?
• Error 34:
Front speakers* are not installed in the correct position.
Left/right of the microphone and speakers may be
installed in reverse.
* The speaker name in this error message depends on the detected
symptom.
• Error 35:
Center speaker* pattern settings and measurement results
do not match. Check the center speaker pattern and
connection.
* The speaker name in this error message depends on the detected
symptom.
• Error 36:
3D position could not be measured. Microphone or
microphone stand may be misaligned. Return to the
correct position and try again. If noisy, measure with as
little surrounding noise as possible.
• Error 37:
– No sound was detected from either the left or right surround
speakers. Is the power for the wireless speakers that are
used as the surround speakers turned on?
– No sound was detected from either the left or right surround
back speakers. Is the power for the wireless speakers that
are used as the surr. back speakers turned on?
– To output audio from the connected wireless speakers,
update software to the latest version. Press [HOME] on the
remote for this unit and select "Setup" to update.
• Error 38:
It wasn't possible to measure correctly. Move the speaker
or microphone position a little and try again. If noisy,
measure with as little surrounding noise as possible.
• Warning 40:
Measurement complete, but it is noisy. It may be possible
to measure again, but it is not possible to measure in all
environments. Measure with as little surrounding noise as
possible.
• Warning 41, Warning 42:
The input from the measurement microphone is excessive.
The speaker and microphone may be too close. Place the
speaker and microphone away from each other. If using
this unit as a preamplifier, this message may be displayed
depending on the connected power amplifier, but it can be
used as it is.
• Warning 43:
The subwoofer distance and phase could not be measured.
Noise may be the cause. Re-measure in a quiet
surrounding environment.
• Warning 44:
Measurement finished, but the center speaker* positional
relationship may be unsuitable. Check the speaker position
referring to "Installing speakers" in the Help Guide.
* The speaker name in this warning message depends on the
detected symptom.
• NO WARNING:
There is no warning information.
Saving/loading settings of the receiver
You can save the settings to a USB flash drive and restore
the saved settings to the receiver or to another receiver of
the same model.
Saving Loading
To save the settings
Insert a USB flash drive to the USB port on the front panel of
the receiver.
Select [Setup] - [Install Settings] - [Save/Load] - [Save] from
the home menu.
To load the settings
Insert to the USB port on the front panel of the receiver a
USB flash drive on which the settings are saved.
Select [Setup] - [Install Settings] - [Save/Load] - [Load] from
the home menu.
13
EN