Stiga G 300 Manual De Instrucciones página 10

6. Cut the ends of the cables to the exact length.
7. Apply the self-drilling connectors on the cable
(Fig. 9.F),(Fig. 9.G),(Fig. 9.H).
8. Connect the connectors to the terminals (Fig. 8.I).
9. Fix the charging base (Fig. 10 L) to the ground with the
fixing screws (Fig. 10.M).
10. Put the cover back on (Fig. 10.C).
11. Connect the power supply plug to the electrical outlet.
12. Check that when the robot lawn mower is not in the charging
base, the warning light on the charging base (Fig. N) is lit
with a fixed light (see Chap. 3.3)
NOTE: The perimeter cable used for installation must be at
least 40 m. long. If the cable is shorter, it will be necessary
to install the resistor code 122063053/0. Please refer to
the Smart User Manual.
2.4. CHARGING THE ROBOT LAWN MOWER
AFTER INSTALLATION
When charged for the first time, the batteries must remain
connected for at least 2 hours.
2.5. PRODUCT SETTINGS
The automatic operation of the robot lawn mower requires a
series of settings that can be made via mobile device (smart
phone) iOS or Android with the "STIGA GO" App installed.
NOTE: For a more detailed description of the available
functions, please refer to the Smart User Manual.
3. OPERATION
3.1. MANUAL FUNCTIONING OF THE ROBOT
LAWN MOWER
The robot lawn mower can be used without performing the
described programming (See Par. 2.5). In this mode the robot
lawn mower carries out a work cycle, returns to the charging
base and remains there until the next manual start.
1. Place the robot mower on the charging base or within the
perimeter of the installation.
2. Press the "STOP" push button (Fig. 1.A) to open the cover
(Fig. 1.B) and access the control panel (Fig. 1.C).
3. Press the "ON/OFF" push button (Fig. 1.E) for 5 seconds
to switch on the robot lawn mower.
4. Press the 'MODE SELECTION' button (Fig.1.F), until only
the icon flashes (Fig. 1.L).
5. Press the "CONFIRM" push button (Fig. 1.G). The icon
(Fig. 1.L) is lit with a fixed light to confirm the operation.
6. Close the cover (Fig. 1.B). The robot lawn mower will
start operating.
NOTE: this mode may not guarantee adequate coverage
of the garden, both in terms of time required and in terms
of uniformity of the cutting result, especially if the garden
has an irregular shape. To achieve the maximum efficiency
of the robot lawn mower, it is recommended to carry out
programming (See Par. 2.5).
3.2. DESCRIPTION OF THE CONTROLS ON THE
ROBOT LAWN MOWER
List of controls, indicators and their function:
• Press the "STOP" push button (Fig. 1.A): it is used to stop
the robot lawn mower safely.
EN
• "SAFETY KEY" (Fig. 1.D): it is used to stop the robot lawn
mower safely.
• "ON/OFF" push button (Fig. 1.E): is used to turn the robot
lawn mower on and off and to reset the alarms.
• "SELECT MODE" push button (Fig. 1.F): it is used to select
the operating mode of the robot lawn mower and to force
it to return to the charging base.
• "CONFIRM" push button (Fig. 1.G): it is used to confirm
the set operating mode.
• "SCHEDULED PROGRAMME" luminous icon (Fig. 1.l):
it is used to display the scheduled programme settings.
• The "SINGLE WORK CYCLE" light icon (Fig.1.L): is used
to display the single work cycle settings.
• "RETURN TO BASE" luminous icon (Fig. 1.H): it is used to
display the settings of the forced return of the robot lawn
mower to the charging base.
• "BLUETOOTH" push button (Fig. 1.M): it is used to display
the blue tooth status.
• "ALARM" luminous icon (Fig. 1.N): it is used to display
alarm statuses.
• "BATTERY" luminous icon (Fig. 1.O): it is used to display
the battery charge level.
NOTE: For a more detailed description of the commands
listed above, please refer to the Smart User Manual.
3.3. CHARGING BASE OPERATION
The charging base is equipped with a warning light (Fig. 10.N)
which lights up as shown below:
• Warning light off: the charging base is powered off or the
robot is on the base;
• Fixed warning light: the perimeter cable is correctly
connected to the charging base, and the perimeter signal
is correctly transmitted;
• Warning light with slow flashing: the perimeter cable is
not connected or it's interrupted;
• Warning light with fast flashing: the perimeter cable is too
short or there is a fault in the charging base.
3.4. BATTERY CHARGING
The "BATTERY CHARGING" procedure allows to recharge
the robot lawn mower manually.
1. Position the robot lawn mower on the charging base
(Fig. 11.R).
2. Slide the robot lawn mower onto the charging base, until
the charging connector is engaged (Fig. 11.S).
3. Press the "STOP" push button (Fig. 11.A) to open the
cover (Fig. 11.B) and access the control panel (Fig. 11.C).
4. Turn the robot lawn mower on with the "ON/OFF" button
(Fig. 11.E).
5. The "BATTERY" luminous icon (Fig. 11.L) flashes, the
robot lawn mower is charging.
6. Close the cover (Fig. 11.B).
7. Leave the robot lawn mower charging for at least the time
shown in Par. 2.4.
NOTE: Charging the battery before winter storage should
be carried out as illustrated in Par. 4.3.
3.5. CUTTING HEIGHT ADJUSTMENT
1. Press the "STOP" button (Fig. 12.A) to open the cover
(Fig. 12.B) and access the control panel (Fig. 12.C).
2. Remove the safety key (Fig. 12.D).
3. Use the height adjuster (Fig. 12.P) to select the desired
4