Publicidad
Idiomas disponibles
Idiomas disponibles
3. Clean any sawdust that may have accumulated in the
guard or clamp washer area and check the condition
and operation of the lower blade guard as previously
outlined. Do not lubricate this area.
4. Select the proper blade for the application (see Blades).
Always use blades that are the correct size (diameter)
with the proper size and shape center hole for mounting
on the saw spindle. Always assure that the maximum
recommended speed (rpm) on the saw blade meets or
exceeds the speed (rpm) of the saw.
5. Follow steps 1 through 5 under To Install the
Blade, making sure that the blade will rotate in the
proper direction.
Lower Blade Guard
WARNING: The lower blade guard is a safety
feature which reduces the risk of serious personal
injury. Never use the saw if the lower blade
guard is missing, damaged, misassembled
or not working properly. Do not rely on the
lower blade guard to protect you under all
circumstances. Your safety depends on following
all warnings and precautions as well as proper
operation of the saw. Check lower blade guard
for proper closing before each use as outlined
in Further safety Instructions for all saws.
If the lower blade guard is missing or not
working properly, have the saw serviced before
using. To assure product safety and reliability,
repair, maintenance and adjustment should be
performed by an authorized service center or
other qualified service organization, always using
identical replacement parts.
Checking the Lower Guard (Fig. A)
1. Turn tool off and disconnect from power supply.
2. Rotate the lower blade guard retracting lever
the fully closed position to the fully open position.
3. Release the lever and observe the guard
fully closed position.
The tool should be serviced by a qualified service center if it:
•
fails to return to the fully closed position,
•
moves intermittently or slowly, or
•
contacts the blade or any part of the tool in all angles
and depth of cut.
Depth of Cut Adjustment (Fig. F, G)
1. Raise the depth adjustment lever
2. To obtain the correct depth of cut, align the appropriate
mark on the depth adjustment strap with notch on the
upper blade guard.
3. Tighten the depth adjustment lever.
4. For the most efficient cutting action using a carbide
tipped saw blade, set the depth adjustment so that
about one half of a tooth projects below the surface of
the wood to be cut.
from
10
8
return to the
15
to loosen.
5. A method of checking for the correct cutting depth
is shown in Fig. F, G. Lay a piece of the material you
plan to cut along the side of the blade, as shown in the
Figure, and observe how much tooth projects beyond
the material.
Adjusting Depth Adjustment Lever
(Fig. F, G)
It may be desirable to adjust the depth adjustment lever
It may loosen in time and hit the base plate before tighten‑
ing.
To Tighten the lever
1. Hold depth adjustment lever
2. Adjust the depth adjustment lever by rotating it in the
desired direction about 1/8 of a revolution.
3. Retighten nut.
Bevel Angle Adjustment (Fig. H)
The full range of the bevel adjustment is from 0 ° to 45 °. The
quadrant is graduated in increments of 1 °. On the front of
the saw is a bevel angle adjustment mechanism consisting of
a calibrated quadrant and a bevel adjustment lever
To Set the Saw for a Bevel Cut
1. Loosen (counterclockwise) the bevel adjustment lever
and tilt shoe (
7
, Fig. A) to the desired angle by aligning
the pointer with the desired angle mark.
2. Retighten lever firmly (clockwise).
Kerf Indicator (Fig. I)
The front of the saw shoe has a kerf indicator
and bevel cutting. This indicator enables you to guide the
saw along cutting lines penciled on the material being cut.
The kerf indicator lines up with the left (inner) side of the
saw blade, which makes the slot or "kerf" cut by the moving
blade fall to the right of the indicator. Guide along the
penciled cutting line so that the kerf falls into the waste or
surplus material.
Mounting and Adjusting the Parallel Fence
(Fig. J)
The parallel fence
19
is used for cutting parallel to the edge
of the workpiece.
Mounting
1. Slacken the parallel fence adjustment knob
the parallel fence to pass.
2. Insert the parallel fence in the base plate
3. Tighten the parallel fence adjustment knob.
Adjusting
1. Slacken the fence adjustment knob and set the parallel
fence to the desired width. The adjustment can be read
on the parallel fence scale.
2. Tighten the fence adjustment knob.
Mounting the Dust Extraction Spout
(Fig. F, Q, R)
Your DWE5615 circular saw is supplied with a dust
extraction spout.
ENGlIsh
15
and loosen the locknut.
15
.
5
16
for vertical
to allow
17
7
as shown.
.
5
27
Publicidad
