Emerson AVENTICS PE7 Instrucciones De Montaje página 7

1 About this documentation
These instructions contain important information for the safe and proper han-
dling of the product.
This documentation is a supplement to the applicable assembly instructions.
Read the assembly instructions completely before working with the product.
1.1 Documentation validity
This documentation provides supplementary information for handling pressure
sensors of series PE7.
This documentation is intended for:
Programmers, service personnel, system owners
1.2 Additional documentation
Observe the following related documents:
• Manufacturer's system documentation
• Documentation of other system components
• Assembly instructions (R412028734)
1.3 Abbreviations used
This documentation uses the following abbreviations:
Abbreviation Meaning
NBR Nitrile Butadiene Rubber (acrylonitrile butadiene rubber)
PELV Protective Extra Low Voltage
PPE Personal protective equipment
SELV Safety Extra Low Voltage
2 Safety
2.1 About this chapter
• Read the chapter Safety of the assembly instructions and this documentation
completely before working with the product.
• Keep this documentation in a location where it is accessible to all users at all
times.
3 Data and parameters
3.1 Notes on safety
• Do not make parameter changes during operation (injury prevention).
3.2 General settings
Settings overview
Submenu
Outputs
Display
Measure
Zero-Point
Diagnosis
Info
Fact. reset
3.2.1 "Info" menu item
The Info menu item displays information about the product.
Parameters Value range / options
Info Ven. Name
Prod. Name
Serial No
HW version
SW version
AVENTICS™ PE7 | R412028763-BAL-001-AA | English
Meaning
Outputs
Representation on display
Measurement signal
Adjust product to current atmosphere. Fur-
ther information: Assembly instructions. See
g 1.2 Additional documentation.
Diagnosis and diagnostic information
Information on the product
Reset to factory settings
Meaning
Manufacturer name
Product name
Material number
Hardware version
Software version
3.2.2 Easy-Mode
The Easy-Mode is optionally usable for frequently recurring changes or for com-
missioning tests.
Activate Easy-Mode: Swipe to the left in main menu 2 or 3.
u
3.3 Parameter data
3.3.1 Setting parameters
"Measure" menu item
In the Measure menu item, parameters for the measurement signal are set.
Parameters Value range / options
Unit bar
psi
kPa
MPa
mH2O
mmHG
%
Damping Increments of 0 ... 4 s /
0.001 s
Resolution -2
-1
default
+1
3.3.2 Resetting to default values
"Factory Reset" menu item
Submenu
Fact. Reset
3.4 Data protocol
3.4.1 Output data
"Outputs" menu item
In the Outputs menu item, parameters of the outputs are set.
Parameters
Submenu 1 Submenu 2
Out 1
Setting 1 Setting of a digital output (for Out 1 only digital options)
Mode
Logic
Meaning
Pressure unit: bar
Pressure unit: psi
Pressure unit: Kilo Pascal
Pressure unit: Mega Pascal
Pressure unit: meter of water
Pressure unit: millimeter of
mercury
Pressure unit: Percent of
nominal pressure range
Cushioning of the measuring
signal: Time for averaging the
pressure
Reduce measured value to 2
decimal places
Reduce measured value to 1
decimal place
Default setting. 2 decimal
places for pressure unit "bar".
Increase measured value to 1
decimal place
Meaning
The product can be reset to factory settings
via the following path: Settings > Fact. Reset >
Reset? > Yes > Confirm.
The action is successful when the confirma-
tion message Factory reset successful is dis-
played.
Values can be saved and uploaded via IO-
Link.
Value range / op- Meaning
tions
PNP Digital, p-switching
NPN Digital, n-switching
Push-Pull Digital, p-switching
and n-switching (anti-
valent)
Hysteresis Hysteresis mode
Window Window mode
NO Make contact ("Nor-
mally Open")
NC Break contact ("Nor-
mally Closed")
7