Publicidad
Idiomas disponibles
Idiomas disponibles
2. Release the button to lock the nozzle in place.
3. Give the nozzle a firm tug to ensure the nozzle is locked
into place.
Nozzle type
Adjustable (Spray fan/Pencil)
Nozzle
Turbo/Rotating Nozzle
NOTE: The Turbo/Rotating nozzle
suitable for cleaning concrete and masonry. We do not
recommend using this nozzle for car/vehicle cleaning as it can
cause damage to the surface.
Adjusting Spray Pattern of the Adjustable
Nozzle from Spray Fan to Pencil (Fig. G1)
The angle of spray coming out of the spray lance may be
adjusted by rotating the nozzle. This will vary the spray pattern
from approximately a 0 ° narrow high impact stream to a 60 °
wide fan spray. A wide fan pattern distributes the impact of
the water over a larger area, resulting in excellent cleaning
action with a reduced risk of surface damage. Large surface
areas can be cleaned more quickly using a wide fan pattern.
A narrow pencil jet stream distributes the impact of the water
in a concentrated area, resulting in a high impact force on
the cleaning surface. Use a narrow pencil jet stream for deep
cleaning in a concentrated area. However, use it cautiously, as
it may damage some surfaces.
To Attach the Self Priming Suction Hose
(Fig. H)
Use the suction hose to pull water from a bucket or other fresh
water source.
NOTICE: Do not use to suction soap, chemicals, dirty
or corrosive liquids, such as window cleaner, plant food,
fertilizers or bleach. Do not use with salt water.
NOTE: Avoid cross threading when installing the suction hose.
Cross threading will cause leaks.
1. To connect the self priming suction hose
pressure washer unit, thread the suction hose collar
onto the water intake
2. Securely tighten the suction hose collar
NOTE: Always disconnect the suction hose after usage.
3. Place other end of suction hose, with the suction hose
filter
4
on it, into a container of fresh water or a fresh
water source.
4. Adjust the float ball
3
hose filter
stays covered in the liquid.
4
5. Select the correct nozzle to be used. Refer to
Attaching Nozzles.
6. After the job being performed is complete, place the
suction hose into a container of clean water and draw the
clean water through the system to rinse.
Suitable applications
For gentle wide angle
cleaning
For abrasive cleaning
23
(refer to Fig. G2) is
2
to the
18
.
31
by hand.
on the suction hose so the suction
(Original instructions)
Removing Soap Bottle from Storage (Fig. I)
Always completely empty the soap bottle
1. Unlock the telescoping handle
you can access the soap bottle
2. To remove the soap bottle
space in the pressure washer unit, grasp the soap
bottle with one hand and pull it out and away from the
pressure washer unit.
3. To place the soap bottle
soap bottle firmly into the storage slot until it snaps into
the built‑in storage space in the pressure washer unit.
4. Ensure that soap bottle is secured into the storage position
by gently tugging on the soap bottle.
Attaching Soap Bottle (Fig. J)
1. To connect the soap bottle
the nozzle button
soap bottle.
2. Release the quick connect collar to lock the soap bottle
in place.
3. Give the soap bottle a firm tug after the quick connect
collar has locked into place to ensure the soap bottle is
locked into place.
NOTE: The soap bottle should be positioned with the bottle
towards the ground. Do not position the soap bottle above the
spray lance as this will lead to soap dripping on the spray lance.
OPERATION
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start‑up can cause injury.
Installing and Removing the Battery Packs
(Fig. K)
This pressure washer is designed to operate on two battery
packs of equal capacity. The pressure washer will not operate
on a single battery pack, and if using different capacity battery
31
packs, the smaller capacity battery pack, when depleted, will
cause the unit to turn off.
NOTE: For best results, make sure your battery packs are both
fully charged.
For optimum performance and runtime, we recommend
using 4.0Ah (SFMCB204) or 6.0Ah (SFMCB206) battery packs.
The pressure washer requires 2 x batteries to run.
To Install the Battery Packs
WARNING: Ensure speed selector switch is in the OFF,
centred position, before installing battery packs.
CAUTION: Unit stops running when the battery port
cover is open. If the speed selector switch is in the HI or
LO position the unit will power ON when the battery port
cover closes.
ENGLISH
26
before storing.
16
, and slide it upwards so
26
.
26
from the built‑in storage
26
into its storage slot, press the
26
to the spray
gun (
6
toward the spray
gun
and insert the
7
, pull
)
13
Publicidad
