Publicidad
Idiomas disponibles
Idiomas disponibles
EN
TRANSPORT, MAINTENANCE AND STORAGE
Caution! Disconnect the sparking plug cable before installing, adjusting, replacing accessories or storing the device.
This will allow for avoiding accidental turning on of the device.
When not in use, store the device in a dry, secured place inaccessible to unauthorised persons.
Before transporting the device, it is necessary to empty the fuel tank.
Replace worn or damaged parts to ensure the safety. Use original spare parts only. Failure to use original spare parts may in-
crease the risk of failure and lead to body injuries. The device should be repaired only at authorised service centres using original
spare parts. This will minimise the risk of accidents and damage to the equipment.
Store the device in a well-ventilated dry and closed room. When stored for a longer period, empty the fuel tank and the fuel sys-
tem. Do not store the device with fuel in the tank. The device should also undergo the maintenance procedures described in the
instructions manual.
When transporting the device, remove the insertion tool.
Keep all nuts, bolts and screws in good condition to ensure safe device operation.
ADDITIONAL SAFETY INSTRUCTIONS
Wear hearing protectors. Exposure to noise can cause hearing loss.
Use the device with the additional handles provided with the tool. Loss of control can cause personal operator injuries.
When carrying out work during which insertion tool may come into contact with a live, concealed electrical wire or power
supply cable, hold the electrical tool using isolated handles. When the insertion tool is in contact with a live wire, it may cause
the metal parts of the tool to become live, which may lead to an electric shock to the tool operator.
Safety warnings related to drilling with long bits
Always start drilling at low speed so that the bit end has a contact with the workpiece. At higher speeds, the bit will probably
bend and cause injury if it is allowed to rotate freely without contact with the workpiece.
Apply pressure only in a straight line with the bit and do not apply excessive pressure. The bit can bend causing breakage
and loss of control which will result in injury.
HAMMER OPERATION
Preparing for operation
Unpack the device and remove all elements of the packaging. It is recommended to keep the original packaging, as it can be
helpful for further transport and storage of the device.
Select the right work tool: punch or cutter.
Clean the tool, lubricate the holder of the selected tool with a thin layer of grease.
Wear hearing protectors, eye protection, and work gloves.
Clean the selected tool from dirt and rust, and lubricate the holder with a thin layer of grease.
Pull the tool holder cover towards the back of the tool and hold it in this position (II).
Insert the cleaned tool into the opening. If necessary, rotate the tool to make sure it enters the holder without any resistance.
Release the holder. The tool should automatically lock inside the holder with the help of the ratchet mechanism.
Make sure the tool has been seated fi rmly. To do this, simply try pulling the tool out of the holder. If the insertion tool slides out of
the holder, reinstall the tool.
Pull the tool holder towards you and hold it in this position and then pull the tool out of the holder.
Operation mode selection
The device off ers two operation modes: impact drilling and demolition. The operation mode is selected by means of a knob. Press
and hold the knob lock button, and then turn it so that the arrow on the knob indicates one of the symbols. The hammer symbol
indicates demolition and the bit and hammer symbol indicate impact drilling (III).
Caution! If drilling takes place on a vertical or almost vertical surface, screw the additional handle into the hammer housing and
use the handle during operation. This will provide a more comfortable and more stable grip on the hammer, making it easier to
counteract the torque created during operation.
Refuelling
When preparing the refuelling device, it must be positioned in such a way that the fuel fi ller of the tank is facing upwards.
The fuel mixture intended for two-stroke engines is used to drive the device. It is forbidden to use petrol alone. Petrol should
be mixed with oil in the following ratio: petrol : oil - 25 : 1. The mixture should be mixed before pouring into the fuel tank. Mixing
and pouring fuel should be carried out away from fi re sources. Never smoke while refuelling. Refuelling must be carried out at a
distance of at least 3 metres from the starting and work area of the device.
In order to protect the engine, use good quality unleaded petrol and good quality oil for two-stroke air-cooled engines. Do not use
O R I G I N A L
I N S T R U C T I O N S
15
Publicidad
