Publicidad
Idiomas disponibles
Idiomas disponibles
• Press [MODE/ENTER], the display shows "C-XX", "XX" stands for the channel no. Such as "C-01", it
means you are editing channel 1 of the selected scene.
• Select the channel no. you would like to edit by pressing [UP].
• Press [MODE/ENTER] to enter editing for the selected channel , the fixture reacts to your settings. The
display shows the DMX value of the edited channel. Such as " 11XX", it stands for channel 11 of the current
scene, the DMX value is XX , XX is a hexadecimal number value "01-FF".
• Adjust the desired DMX value by pressing [UP] or [DN].
• Press [MODE/ENTER] in order to edit other channels of this scene.
• Repeat above steps until you finish setting all the DMX values for all channels of this scene.
• Once all the channels completed, the display will flash "TIME".
• Press [MODE/ENTER] to edit the time needed, the display shows "TXXX","X" stands for the time needed to
run the current scene, value "001-999". For example, "T002" means you need 2 seconds to run the current
scene.
• Adjust the desired time by pressing [UP] or [DN].
• Press [MODE/ENTER] to save the settings for the scene you are editing, the display will change to the next
scene automatically.
• Repeat above steps to edit and other scenes, you can edit and save a maximum of 48 scenes.
• Press [EXIT] to exit. The number of steps can be defined under "STEP" and the scenes can be called up
under "RUN"
b) Editing via the external controller
• Call up the first scene in your controller now.
• Select "SC01" by pressing [UP] or [DN].
• Press [MODE/ENTER], the display shows "SC01".
• Press [MODE/ENTER], the display shows "C-01".
• Select "CNIN" by pressing [UP] or [DN].
• Press [MODE/ENTER], the display shows "OFF".
• Press [UP], the display shows "ON".
• Press [MODE/ENTER], the display shows "SC02". You successfully downloaded the first scene.
• Adjust the Step-time as described above.
• Call up the second scene in your controller now.
• Repeat steps 5-11 until all desired scenes are downloaded.
• Press [EXIT] to exit. The number of steps can be defined under "STEP" and the scenes can be called up
under "RUN"
Error Messages
When you turn on the fixture, it will make a reset first. The display may show "XXEr" while there are
problems with one or more channels. "XX" stands for the channels equipped with a testing sensor.
For example, when the display shows "04Er", it means there is some error in channel 4. If there are
some errors on channel 4, channel 5, channel 6 at the same time, you may see the error message
"04Er", "05Er","06Er" flash repeatly for 5 times, and then the fixture will generate a reset signal, all
the stepper motors will reset. If the error messages maintain after performing reset more than 3
times, it will detect whether the fixture has more than 3 errors. If the fixture has more than 3 errors
(including 3 errors), all the channels can not work properly; but if the fixture has less than 3 errors,
only the channels which have errors can not work properly, others can work as usual.
01Er:
(Color-wheel error) This message will appear after the reset of the fixture if the magnetic-indexing circuit
malfunctions (sensor failed or magnet missing) or the stepping-motor is defective (or its drive circuit on the
main PCB). The color wheel is not located in the default position after the reset.
02Er:
(Rotating gobo-wheel error ) This message will appear after the reset of the fixture if the magnetic-indexing
circuit malfunctions(sensor failed or magnet missing) or the stepping-motor is defective (or its drive circuit on
the main PCB). The rotating gobo-wheel is not located in the default position after the reset.
03Er:
(Rotating gobo indexing error) This message will appear after the reset of the fixture and if the magnetic-
indexing circuit malfunctions (sensor failed or magnet missing) or the stepping-motor is defective (or its driver
circuit on the main PCB). The rotating gobo is not located in the default position after the reset.
52/104
51837570_V_1_0.DOC
Publicidad
