Titan LX60 Instrucciones página 2

Operating the High Pressure Spray Gun
The gun is designed for pressures up to 3600 PSI, 248 bar.
POSSIBLE INjEcTION HAZARD - Do not spray without the tip
assembly in place. Never trigger the gun unless the tip is in
either the spray or the unclog position. Always lock the trigger
off when attaching the spray tip or when the spray gun is not in
use.
Locking the Spray Gun
Always lock the gun off when it is not in use. To lock the gun, turn the trigger lock
forward and slightly down until it stops. To unlock the gun, turn the trigger lock
so that it is vertical and pointing up.
Trigger locked
(gun will not spray)
Attaching the Tip Assembly
1. Thread the spray guard assembly onto the gun. Tighten by hand.
unclogging the Spray Tip
Do not attempt to unclog or clean the tip with your finger. Do
not use a needle or other sharp pointed instrument to clean the
tip. The hard tungsten carbide is brittle and can be chipped.
The spray gun is equipped with a reversible tip which allows you to blow out
any particles of old paint or other contaminants that may obstruct the paint
flow through the tip. If the spray pattern becomes distorted or stops completely
while the gun is triggered, follow these steps:
1. Follow Pressure Relief Procedure (see sprayer instruction manual)
2. Rotate spray tip 180 degrees from its
current position.
3. Unlock the gun and squeeze the trigger,
pointing the gun at a scrap piece of wood
or cardboard. This allows pressure in the
spray hose to blow out the obstruction.
When the nozzle is clear, paint will come
out in a straight, high pressure stream.
4. Release the trigger and lock the gun off.
5. Rotate spray tip forward to one of the
SPRAY positions.
6. Unlock the gun and resume spraying.
cleaning the Gun
ImPORTANT: If spraying with latex paint, use warm soapy water for
cleaning. If using oil or alkyd-based paints, use mineral spirits or paint
thinner. Refer to the paint manufacturer's instructions for specific
recomendations.
Do not use mineral spirits or paint thinner on latex paint, or the mixture will
turn into a jellylike substance which is difficult to remove.
1. Check that the spray tip assembly has been removed from the gun.
2. Run the appropriate solvent through the
pump.
3. Hold the metal part of the gun against a metal
container to ground the gun.
4. Trigger the gun into the container until it is
flushed clean. Use the lowest possible pressure.
English English
Trigger unlocked
(gun will spray)
cleaning the Filter
This filter must be cleaned every time you use your sprayer. When using thicker
paints, the filter might need to be cleaned more often.
1. Unclip the trigger guard from the filter housing by pulling outward from
the filter housing. Unscrew the housing.
Trigger
guard
2. Remove the filter from the spray gun housing and clean with the
appropriate cleaning solution (warm, soapy water for latex paints,
mineral spirits for oil-based materials).
3. Inspect the filter for holes (see Hole picture, above). Replace if holes are
found.
ImPORTANT: Never poke the filter with a sharp instrument!
4. Replace the cleaned filter, tapered end first, into the gun housing.
5. Replace the housing and spring and snap the trigger guard back into the
housing.
Parts List
1
2
Item Part # Description
1 0516711 Tip guard ................................................................................ 1
2 0516704 Tip, 517 ................................................................................... 1
3 0516719 Complete gun assembly................................................... 1
4 0516737 Filter, white (2 pack) ........................................................... 1
5 560-038 Handle seal ............................................................................ 1
6 0296342 Handle ..................................................................................... 1
7 0347706 Swivel ...................................................................................... 1
2
Threaded
end
( lter top)
Filter
Hole
Filter housing
3
4
5
© Titan Tool Inc. All rights reserved.
6
7
Quantity