Rupes BA225S Traducción De Manual De Instrucciones Original página 10

Do not operate the electrical tool while carrying it at the side. Accidental
contact with the rotation accessory can get your clothes entangled and attract
the accessory towards you.
Regularly clean the fan openings of the electrical tool. The motor fan will
attract the dust into the housing; excess dust accumulation can cause electrical
hazards.
Do not operate the electrical tool in the proximity of flammable material. The
sparks can ignite these materials.
Do not use accessories that need liquid coolants. The use of water or other
liquid coolants can cause electrocution or electrical shock
ADDITIONAL SAFETY WARNINGS FOR GRINDING AND ABRASIVE
CUTTING OPERATIONS
Use only the type of cutting/grinding wheels recommended for your tool
and the protection specifically designed for the selected cutting/grinding
wheel. Cutting/grinding wheels not designed to be used with the tool cannot be
adequately protected and are unsafe.
The protection must be solidly fixed to the tool and placed in the safest
position possible so as to minimise the potential risk of contact between
the operator and cutting/grinding wheel. The protection is designed to protect
operators from the ejection of fragments in case of breakage and from accidental
contacts with the grinding wheel.
Cutting/grinding wheels must be used for the recommended applications
only. For example do not use the cutting side of the wheel for grinding
operations. Abrasive cutting wheels may break because they are designed to
be used for peripheral grinding operations and for the application of lateral
forces.
Always use the cutting/grinding wheels with undamaged flanges and verify
that their shape and dimensions are appropriate for the selected
cutting/grinding wheel. The purpose of flanges is to support the cutting/
grinding wheel and reduce the potential risk of breakage. Flanges forcutting
wheels may be different from those of grinding wheels.
Do not use grinding/cutting wheels that have been fitted on larger tools.
These cutting/grinding wheels are unsuitable because of their higher speed as
compared to that of smaller tools and could therefore cause explosions.
ADDITIONAL SAFETY WARNINGS FOR ABRASIVE
CUTTING OPERATIONS
Do not "stall" the cutting wheel or apply an excessive pressure. Do not
attempt to increase the cutting depth. The application of a high pressure on
the cutting wheel increases the load and the risk of torsion and bending during
cutting, with the consequent risk of rebound forces or breakage.
Do not stand in line with the cutting/grinding wheel or behind it while it is
rotating. When the cutting/grinding wheel moves away from the operator's body
during operation, the rebound force may push the revolving cutting/grinding
wheel and the tool towards the operator.
If the cutting/grinding wheel bends or the cutting operations stops for any
reason, disconnect the tool from the power supply and keep it still until the
cutting/grinding wheel has come to a full stop. Do not attempt to remove the
10
cutting wheel while it is moving because this could produce a rebound force.
Identify the cause of the problem and perform the necessary corrective actions
to prevent the problem from reoccurring.
Do not resume the cutting operation. Resume the cutting operation only
when the cutting wheel has reached its maximum speed. The cutting wheel
may stall, lift or produce a rebound force if the tool is restarted when the work
piece is present.
Always use appropriate supports for panels or large work pieces in order to
minimisethe risk of interlocking and rebound forces. Large work pieces tend
to bend because of their weight. Supports must therefore be placed under the
work piece, close to the cuttingline and to the edge of the work piece on both
sides.
Pay particular attention when cutting "pockets" on existing walls or other
areas with limited visibility. The projecting cutting wheel may cut gas or water
pipes, electrical cables or other objects and thus produce a rebound force.
SPECIFIC SAFETY WARNINGS FOR METAL BRUSHING:
Keep in mind that the brush, even during normal operation, emits metal
bristles. Do not apply excessive force to the metal wires, by applying
excessive force to the brush.
clothing and/or hair.
If use of protection for the metal brushing is recommended, do not allow any
interference of the disc to the metal wires or of the brush with the protection.
The disc with metal wires or the brush can expand in diameter due to the work
load and centrifugal forces.
FURTHER HAZARD WARNINGS
Avoid having dust accumulated on the work station. The dust can easily ignite.
A work piece can be safely locked in position only using an appropriate
tightening device or a screw clamp and not just holding it with your hand.
Adjust the protective earmuffs so as to impede a trail of sparks in the
direction of the operator. Do not touch the rough and cut grinding wheels
before they are cooled. Activate the locking key of the spindle only when the
spindle is stopped. Otherwise, the electrical tool may suffer damages.
Wear protective goggles
The metal bristles can easily penetrate light